min2plus

设计一个一位二进制数大小比较器。比较两个一位二进制数A和B的大小，电路有三个输出端Y1，Y2和Y3，分别对应A大于B，A等于B，A小于B。当条件满足时，相应输出端为1，否则为0。（A，B用两个脉冲源代替），建立仿真模型并保存。(Design a one binary magnitude comparator. A size comparison of two binary numbers A and B, the circuit has three outputs Y1, Y2 and Y3, respectively, corresponding to the A greater than B, A is equal to B, A less than B. When the conditions are met, the corresponding output is 1, and 0 otherwise. (A, B instead of the source with two pulses), and save the simulation model.)

标准压缩感知（CS）理论决定了可靠的信号恢复是可能给M= O（KLOG（N / K））的测量。我们证明了它可以通过利用超越简单的稀疏性和可压缩性由包括价值观和信号系数的位置之间的依赖关系更加逼真信号模型大大降低Mwithout牺牲的鲁棒性。(The standard compressive sensing (CS) theory dictates that robust signal recovery is  possible from  M=O(Klog(N/K))  measurements. We demonstrate that it is possible to substantially  decrease  Mwithout sacrificing robustness by leveraging more  realistic signal models that go beyond simple sparsity and  compressibility by including dependencies between values and  locations of the signal coefficients.   )

matlab NURBS 工具箱，应用于matlab中NURBS曲线、曲面的设计. (NURBS toolbox used in MATLAB, used to the design of NURBS curves and surfaces.)(matlab NURBS (NURBS toolbox used in MATLAB, used to the design of NURBS curves and surfaces.))

几个解耦控制系统的Simulink模型，用过还行。共享一下。(Several decoupling control system Simulink model, used also OK. Sharing about.)

这是关于直接序列扩频通信系统的DS-CDMA方式的仿真设计，系统主要分为发送机和接收机两部分，包括17个可用于SIMULINK仿真的S-FUNCTION代码M文件，和一个MATLAB源程序的DOC文件，程序都有详细的注释。(This is a direct sequence spread spectrum communication system on the DS-CDMA mode simulation design, the system can be divided into two parts, transmitter and receiver, including 17 for the S-FUNCTION SIMULINK simulation of M code files, and a MATLAB source code The DOC file, the program has detailed notes. 朗读 显示对应的拉丁字符的拼音 字典- 查看字典详细内容名词0.directness0.immediacy形容词0.direct0.immediate0.first-hand0.plump副词0.straight0.right0.slap )

一个老外写的文章，很不错，对以后学习核主元分析（KPCA）有帮助！(the paper was written by the foreigner，which is very useful and meaningful.)

用matlab自动生成的DSP代码。。。。 (matlab automatically generated DSP code)

The program RANDOM_WALK_2D_PLOT plots the trajectories of one or more random walks. The program RANDOM_WALK_2D_SIMULATION plots averaged data for any number of random walks that each use the same number of steps. The data plotted is the average and maximum of the distance squared at each time step. The average distance squared should behave like the number of time steps.

Jakes model for multipath fading channel

关节角度的显示和预处理Matlab程序。关于信号的显示保存法，运行环境为Matlab。(The joint angle display and preprocessing of the Matlab program. On the display of signal storage method, the operating environment for Matlab.)