CY7C68013A-56PVXC

实现了UART的底层协议，加入了控制器，其波特率可以根据使用进行调整；发送模块、接收模块相互独立，互不影响。(Realization of the underlying protocol UART, joined the controller baud rate can be adjusted according to use transmission module, receiver module are independent of each other.)

基于51单片机的AD7705的调试程序 经验证很好用 和大家一起分享(51 Microcontroller based debugger AD7705 with proven good to share with everyone)

Zedboard上板载有一个USB转UART串口，采用了Cypress公司的USB-UART控制器CY7C64225。Zedboard的USB驱动安装很简单，首先下载USB驱动程序，解压缩后会有3个子目录分别对应Windows XP、Windows Vista和Windows 7系统，根据自己的计算机系统选择。(Onboard there Zedboard a USB-to-UART serial port, using Cypress' s USB-UART controller CY7C64225. Zedboard USB driver installation is very simple, first download the USB driver, unzip have three subdirectories corresponding to Windows XP, Windows Vista and Windows 7 systems, according to their own computer systems to choose from.)

If there are no Klingons in this quadrant, we nullify any distress calls which might exist.

Energy harvesting broadcast channel with inefficient energy storage Energy harvesting broadcast channel with inefficient energy storage Energy harvesting broadcast channel with inefficient energy storage

采用ＰＩＣ单片机解码ＴＶ红外线遥控器程序,程序采用ＰＩＣ１６Ｆ６３０，可以针对大部分遥控器解码．(using PIC microcontroller decoding TV infrared remote control procedures that are used PIC16F630. can address most of the remote control decoder.)

Keil中实现单片机通过RTL8019A网口芯片访问PC机的功能。(The Keil microcontroller chip access the PC by RTL8019A network port function.)

本总体方案完成国标GB20600-2006数字电视地面广播传输系统基带部分功能。 输入数据码流经过扰码器（随机化）、前向纠错编码（FEC），然后进行比特流到符号流的星座映射，再进行交织后形成基本数据块，基本数据块与系统信息组合（复用）后并经过帧体数据处理形成帧体，帧体与相应的帧头（PN序列）复接为信号帧（组帧），经过基带后处理转换为输出信号（8MHz带宽内）。该信号经变频转换为射频信号（UHF和VHF频段范围内）。用C程序设计了图形交互界面，可以在界面上直接设置调制参数。(The overall program completion GB GB20600-2006 digital terrestrial television broadcasting transmission systems baseband function. The input data stream through the scrambler (randomization), forward error correction (the FEC), then the symbol constellation mapping bitstream to the stream, and then after forming the basic block interleaving, the basic data block and information combined system ( multiplexing) after data processing and after the frame body forms a frame body, frame body with a corresponding header (PN sequence) multiplexed signal frame (framing), after post-processing baseband signal is converted to an output (internal 8MHz bandwidth). The signal is downconverted to a radio frequency signal (in the VHF and UHF frequency range). C program designed graphical interface, you can set modulation parameters directly on the screen.)

-lpc2148 -sdcard -vms board

arduino RTC connect on DS1307 2