-
matlab--AGC
实现MATLAB下的音频AGC,关键是要有高效的算法。效果不错。(MATLAB realize the audio AGC, the key is to have efficient algorithms. Good results.)
- 2008-05-14 22:03:39下载
- 积分:1
-
binary_ga
A simple binary Ga for optimization.
- 2012-04-30 03:52:51下载
- 积分:1
-
wifi_matlab
matlab中用m文件和Simulink共同实现WIFI的仿真,学习的好资料!(matlab with m documents and a common realization of Simulink simulation WIFI, learning good information!)
- 2009-01-14 20:40:44下载
- 积分:1
-
selfCorrelationInRandomization
产生零均值单位方差高斯白噪声的1000个样点,估计随机过程的自相关序列(units have zero mean Gaussian white noise variance to the 1,000-point, it is estimated that the random process autocorrelation sequence)
- 2007-05-15 22:34:06下载
- 积分:1
-
SBOCCrare
几个BOC 信号的分析例程,全球卫星导航系统将普遍使用BOC调制信号作为扩频测距信号,BOC信号号自相关函数呈现多个相关峰,传统扩频接收机所用的延迟锁定环(DLL)无法对该信号正确地进行码相位的
(Several BOC signal analysis routines, the global satellite navigation system will generally use the BOC modulation signal as a spread spectrum ranging signal, BOC signal autocorrelation function presents multiple correlation peaks, the traditional spread spectrum receiver with the delay locked loop (DLL ) can not be the signal code phase)
- 2012-08-20 14:37:00下载
- 积分:1
-
ofdm
该程序源代码实现了OFDM通信系统性能的仿真,调制方式有BPSK,QPSK,MSK,QAM,信道为AWGN和Rayleigh信道,并对有插入导频的符合IEEE802.11a的OFDM系统进行了仿真。(The program source code to achieve the performance of OFDM communication system simulation, modulation has BPSK, QPSK, MSK, QAM, for the AWGN channel and Rayleigh channel, and have inserted the line with the IEEE802.11a pilot of OFDM system simulation.)
- 2007-08-19 10:55:24下载
- 积分:1
-
OPM-matlab
基于压缩感知的匹配基追踪算法的matlab实现(Based on compressed sensing based tracking algorithm matlab matching)
- 2020-11-16 21:59:40下载
- 积分:1
-
jiyuMATLABdefangzhenyanjiu
基于matlab的直流伺服电机驱动进给系统的仿真研究 ,(Matlab-based DC servo motor drive feed system simulation,)
- 2013-05-14 10:40:35下载
- 积分:1
-
Boost_Converter
说明: 升压转换器是一种DC / DC电源转换器,可将电压从其输入(源)升至其输出(负载)。在连续导通模式下(流经电感的电流永远不会降为零),升压转换器的理论传递函数为:
占空比在哪里0.5
在此示例中,转换器从250 V电源馈送RC负载,并且PWM频率设置为31 kHz。
模拟
运行仿真并观察示波器上的波形。确认负载电压(Vout)的平均值非常接近理论值:Vout = 250 /(1- 0.5)= 500V。(A boost converter is a DC/DC power converter which steps up voltage from its input (source) to its output (load). In continuous conduction mode (current through the inductor never falls to zero), the theoretical transfer function of the boost converter is:
where is the duty cycle.0.5
In this example, the converter is feeding an RC load from a 250 V source and the PWM frequency is set to 31 kHz.
Simulation
Run the simulation and observe waveforms on Scope. Verify that the mean value of the load voltage (Vout) is very close to the theoretical value of: Vout = 250 / (1 - 0.5) = 500 V.)
- 2020-03-22 20:41:56下载
- 积分:1
-
ProbabilityandStochastics
Probability and Stochastics蒙特卡洛算法等(Probability and Stochastics)
- 2021-03-21 21:49:16下载
- 积分:1