ST7789S-G4A-APPLICATION-PACKAGE

its all about the finger print recognition

ALIENTEK STM32开发板SYSTEM文件夹，采用V3.5库的头文件，使得代码可以完美移植到库函数里面使用，不过注意，在新建工程的时候，请在：Options for Target-->C/C++ 选项卡里面 Preprocessor Symbols 栏定义你的STM32芯片容量。比如:ALIENTEK 战舰STM32开发板用户，使用的是大容量的STM32芯片，则在Define栏输入：STM32F10X_HD 对于STM32F103系列芯片，设置原则如下： 16KB≤FLASH≤32KB 选择：STM32F10X_LD 64KB≤FLASH≤128KB 选择：STM32F10X_MD 256KB≤FLASH≤512KB 选择：STM32F10X_HD(ALIENTEK STM32 development board SYSTEM folder, using V3.5 library header file, so that code can be perfectly transplanted to the library function to use, but note that in the new project, please: Options for Target - > C/C++ tab in the Preprocessor Symbols column to define your STM32 chip capacity. For example: ALIENTEK warship STM32 development board users, using a large capacity STM32 chip, in the Define column input: STM32F10X_HD For STM32F103 series chips, the setting principles are as follows: 16KB < FLASH < 32KB Selection: STM32F10X_LD 64KB < FLASH < 128KB Selection: STM32F10X_MD 256KB < FLASH < 512KB Selection: STM32F10X_HD)

这是Keil C51中的两个例子，对于刚刚接触Keil C51的人来说这两个例子非常有用 (This is the Keil C51 two examples, For contact Keil C51 just who these two examples very useful)

说明：  基于stc15的电子密码锁设计，带原理图(Design of electronic password lock based on stc15 with schematic diagram)

AVR入门初级小程序，流水灯，定时器，中断等(AVR Starter primary applet, water lights, timers, interrupts, etc.)

Study on LD Pumped Yb3+ -doped Double-clad Fiber Lasers数值分析对线形腔LD泵浦掺镱的双包层光纤激光器进行研究，分析了单端泵浦和双端泵浦的泵浦光及激光输出功率和增益在光纤中的分布，结果表明，非均匀泵浦比较适合高功率光纤激光器。(Study on LD Pumped Yb3+-Doped Double-clad Fiber Lasers numerical analysis of the linear cavity of the LD-pumped Yb-doped double-clad fiber laser research, analysis of single-ended and double-end-pumped pumped pumped optical and laser output power and gain distribution in optical fibers, results show that more suitable for non-uniform-pumped high power fiber lasers.)

POS Cell Zone for Visual Basic

说明：  一个和泰芯片上面用过的TM1638程序，一些初始化和显示，分固定地址和全写。(A TM1638 program used on Hetai chip, some initialization and display, divided into fixed address and full write.)

说明：  介绍了用8031 单片机控制的电脑数字钟的硬件结构与软件设计。给出了汇(Introduced the 8031 microcontroller using a computer controlled digital clock in the hardware structure and software design. Gives the Department of)

模拟电路讲义上册 总共201页 全书五个章节， 第一张晶体管 第二章运放 第三章振荡器 第四章模拟锁相 第五章数模转换 第六章滤波器 第七章反馈(A total of 201 pages of lecture notes for analog circuits There are five chapters in the book. The first transistor The second chapter is op amp. The third chapter oscillator The fourth chapter is analog phase-locked. The fifth chapter is digital to analog conversion. The sixth chapter filter The seventh chapter feedback)