AT90S2313-Push-Switch-Led-Blinking

德州仪器(TI) 的超低功耗16 位RISC 混合信号处理器的MSP430 平台为电池供电的测量应用提供了最终解决方案。应用包括便携式医疗设备、低功耗工业操作、无线、实用计量等(Texas Instruments (TI) ultra-low-power 16-bit RISC mixed-signal processor MSP430 platform for battery-powered measurement applications to provide the ultimate solution. Applications include portable medical equipment, low-power industrial operation, wireless, utility metering, etc.)

单片机的protues仿真实验，包括单片机最小系统，AD1208，DA1674,AT24C02的仿真(SCM protues simulation experiments, including the smallest single-chip system, AD1208, DA1674, AT24C02 simulation)

以1/10秒为单位，向电脑串口发送数据。同时，在P2口上以2进制形式显示发送的数字。可作为调试的工具。(Send a number to the computer s COM port, for each 0.1 second. while display it on port P2.)

stm8l的ADC采集，DAC输出以及串口通讯(Stm8l ADC acquisition, DAC output and serial communication)

温度传感器LM75A的中文应用资料，来自周立功公司，该资料阐述了LM75A的内部结构，并给出了应用实例和源码。(Temperature sensor the LM75A the Chinese application data from ZLG, the information set forth LM75A the internal structure, and gives application examples and source code.)

说明：  用TIM1输出6路互补的SPWM，实现电机转动，用VF调频调压(Six complementary SPWM outputs from TIM1 are used to realize motor rotation and VF frequency and voltage regulation.)

标题： NEC红外线接收解码程序引用定时器 效果： 运行程序，按遥控器按键，在数码管上显示相应的地址码-控制码（以16进制显示） 分两段，前段是地址码，后段为控制码，用点隔开，显示两字节，忽略反码(Title: NEC infrared receiver decoder program reference timer effect: run the program, press the button of the remote control, digital display corresponding address code- control code (displayed in hexadecimal) separated into two parts, the preceding address code, after paragraph control codes, separated by dots, two bytes, to ignore the anti-code)

编制MCS-51程序使步进电机按照规定的转速和方向进行旋转，并将已转动的步数显示在数码管上。 　　步进电机的转速分为两档，当按下S1开关时，加速旋转，速度从10转/分加速到60转/分。当松开开关时，减速旋转，速度恢复为10转/分。当按下S2开关时，按照逆时针旋转；当松开时，按照顺时针旋转。 　　本程序要求使用定时器中断来实现，不准使用程序延时的方式。(The MCS-51 program is programmed to rotate the stepper motor according to the specified speed and direction, and the number of steps that have been rotated is displayed on the digital tube. Stepper motor speed is divided into two gears. When the S1 switch is pressed, the speed is accelerated from 10 rpm to 60 rpm. When the switch is loosened, the speed will be reduced to 10 rpm. When pressing the S2 switch, rotate counterclockwise; when loosening, rotate clockwise. This procedure requires the use of timer interrupt to achieve, do not use the way of program delay.)

ez80L92系列汇编语言 单片机的始祖，不过在工控领域还是有人在使用。24位单片机(ez80l92 assembly language)

说明：  ESP8266 PWM控制一盏LED的亮度变化。(ESP8266 PWM controls the brightness change of an LED.)