-
Householder
本程序是利用Householder变换分解得到Q,U(This program is using Householder transform decomposition of Q, U)
- 2012-03-26 15:30:08下载
- 积分:1
-
refbook
matlab函数参考,工具箱。matlab function references volume1-3.(matlab function reference, toolbox. matlab function references volume1-3.)
- 2013-03-20 10:44:06下载
- 积分:1
-
easyTack_DEMO_V0.1
matlab gui界面 实现目标实时跟踪(real time object tracking)
- 2017-06-08 10:43:22下载
- 积分:1
-
萤火虫算法 CS PSO
以优化SVM算法的参数c和g为例,对CS算法MATLAB源码进行了逐行中文注解。(SVM algorithm to optimize the parameters c and g, for example, the CS algorithm MATLAB source was progressive Chinese annotations.)
- 2016-09-09 17:05:00下载
- 积分:1
-
spinfilter
针对条纹图中的随机散斑噪声,编制旋滤波程序,能够去除散斑噪声的影响,同时不损害条纹信息。(Fringe pattern for the random speckle noise, the preparation of spin filtering procedures to remove the speckle noise, while not jeopardizing the fringe information.)
- 2008-02-10 22:28:02下载
- 积分:1
-
capon
capon波束形成器的波达方向估计仿真,包括直角坐标、极坐标及加权后的波达方向(capon beamformer DOA estimation simulation, including the rectangular coordinates, polar coordinates and the weighted DOA)
- 2011-01-02 16:28:43下载
- 积分:1
-
QPSK-MSK-QAM-OFDM
这个 压缩包含有完整的QPSK-MSK-QAM-OFDM调制解调m程序。希望对大家有帮助(This includes a complete compression QPSK-MSK-QAM-OFDM modulation and demodulation m program. We want to help)
- 2011-01-08 11:31:49下载
- 积分:1
-
chengxu
小波变换进行变速箱故障诊断
首先将s1和s2信号时域谱(s1代表维修前的振动信号,s2代表维修后的振动信号),画出来进行对比,会发现s1信号的振动幅值会比较高;然后对s1和s2分别进行小波分解并画出各层的时域谱,只对比s1和s2分后的最高时域谱,s2更加的具有周期性,且幅值较小,s2周期性不够明显,且振动过于密集。分析完时域谱后开始分析频谱,首先对原信号s1和s2fft转换,得到频谱图,如图,然后再对小波分析后高频部分进行fft转换,做出频谱图。对比后我们发现,在f 2375HZ出(也就是齿轮的啮合频率),s1信号频谱幅值会有急剧的升高,然后,其谐波的幅值也会增大。所以可以推断出该维修前的增速箱的齿轮可能出现问题。(Gearbox fault diagnosis based on wavelet transform s1 and s2 first time domain signal spectrum (s1 behalf of the vibration signal before maintenance, vibration signal s2 representative of repaired), drawn comparison, you will find a signal s1 vibration amplitude will be higher then s1 and s2 respectively wavelet decomposition and draw the layers of time-domain spectrum to only a maximum time domain spectroscopy s1 and s2 points after, s2 is more cyclical and smaller magnitude, s2 cyclical enough obviously, and the vibration is too dense. End domain spectral analysis after the beginning of the spectrum analysis, the first of the original signal s1 and s2fft conversion to give the spectrum, as shown, and then after the high frequency part of wavelet analysis fft transformation to make spectrum. We found that after the comparison, at f 2375HZ out (i.e. the gear mesh frequency), there will be a sharp increase in the amplitude spectrum of the signal s1, and then, the amplitude of the ha)
- 2017-01-17 19:18:02下载
- 积分:1
-
ECG_simulator
matlab simulator用matlab制作有具体ECG制作说明(matlab simulator)
- 2010-08-11 12:32:17下载
- 积分:1
-
analyse-spectrale
documentation sur l analyse spectrale
- 2010-11-20 07:13:58下载
- 积分:1