fichier1

数值分析中几个基础的matlab程序，包括选主元的高斯消去，矩阵的LU分解以及Jacobi迭代(Numerical analysis of several matlab-based procedures, including the election of the principal Gaussian elimination, LU decomposition of matrices and Jacobi iteration)

用matlab中的GUI界面设计了一个可以实现混响的界面(Designed a reverberation of the interface can be achieved using the GUI interface in matlab)

多通道盲源分离（基于极大化非高斯性的负熵算法）源代码(Multi-channel blind source separation (based on the maximization of the negative entropy of non-Gaussian algorithm) source code)

matlab控制电脑摄像头定时拍照加gui界面设计。。。matlab(matlab control computer camera timer camera plus gui interface design. . . matlab)

apsk软判决算法的仿真，根据星座特点进行算法的简化，减低复杂度(Simulation apsk soft decision algorithm based on the characteristics of the constellation simplified algorithm to reduce the complexity of)

采用位置式PID实现炉温控制 采用继电法整定PID参数 (Realized using positional PID temperature control relay method using PID tuning parameters)

该程序很详细的比较分析了协作通信三个节点时系统在直接转发、存储转发AF和DF模式下的理论与仿真误码率曲线。(The program is very detailed comparative analysis of the collaborative communication system in direct forward three nodes, store-and-forward AF and DF mode theory and simulation of the ber curve.)

MatLab环境下编程实现简单交互式单纯形法进行寻优并显示寻优结果。(MatLab environment realize simple interactive programming simplex method for optimization and display the results of optimization.)

随机线性分组编码，信道编码，纠错编码，检错编码(Random linear block coding, channel coding)

首先根据短训练字的特性进行相关运算，进行信号到达检测，当检测到相关值大于门限一定次数后，认为有信号到达。然后根据长训练字的特性，进行相关运算，进行OFDM符号FFT窗口起始位置的估计。估计出FFT窗口的位置后，先在时域进行小频偏的估计，将两个长训练字进行小频偏补偿后，进行FFT运算，根据FFT运算的结果进行整数倍频偏的估计。这些参数估计完成后，就可以进行数据解调了。先对数据部分进行完整的频偏补偿，然后根据估计的FFT窗口位置进行FFT运算得到频域的数据，进行解调。然后在对应于导频的子载波位置上提取出导频信息，根据导频信息估计出剩余定时误差以及剩余的信道响应误差，将误差量送入环路进行跟踪。当收到所有数据后，重新回到信号到达检测状态，进行下一次信号到达的检测和信号接收。(First, according to the characteristics of the short training word correlation operation, the signal reaching the detector, when the detected correlation value is greater than the threshold after a certain number of times that a signal arrives. And then the characteristics of long training word, the correlation operation for the FFT window starting position of an OFDM symbol estimate. The estimated position of the FFT window, the first small frequency offset in the time domain estimation, the two long training word small frequency offset compensation, the FFT operation, the FFT result of the operation for integer frequency offset estimate. These parameter estimation is completed, the data can be demodulated on. The first portion of the data for a complete frequency offset compensation, and based on the estimated FFT window position of the FFT operation to obtain frequency domain data, demodulated. Then corresponding to the position of the pilot subcarriers are extracted on pilot inform)