DC_DC

28035的GPIO配置例程，实现流水灯相关的功能(28035 GPIO configuration routines for implementing water-light related functions)

用于can通讯的 can 总线协议iso 15765的中文翻译，虽然有些地方不大准确，但可以对照英文一起看，方便英文不大好的同学(Communication can be used can bus protocol iso 15765 Chinese translation, although in some places is not accurate, but can be controlled in conjunction with the English, to facilitate the students English is not good)

用2407实现的通过电位器改变占空比，从而调节电机转速，并带有捕捉显示占空比(Implemented with the 2407 change in the duty cycle through the potentiometer to regulate motor speed and duty cycle with the capture display)

mathcad直流电机设计源文件，包含电机设计常见的参数计算过程。对于电机计算具有一定参考价值(mathcad DC motor design source file that contains common motor design parameters calculation. The motor has a certain reference value calculation)

说明：  用DSP28335实现SPWM，包含了头文件(Implementing SPWM, with DSP28335 contains header files)

该模块实现了对转永磁同步电机的矢量控制，保证了两转子转速相等(this mode is something about anti-rotary PMSM control)

改主板设计是源于三相控制，用于逆变器的主控板，支持LCD,KEY,SVPWM ,AD 等 功能齐全。(Change the motherboard design is derived from phase control for inverter, the master control board, support LCD, KEY, SVPWM, AD and other functions.)

TMS320vc5416DSP bootloader的程序，运行的平台为CCS(TMS320vc5416DSP bootloader procedure, run a platform for CCS)

radar basics and about two a4 sheets.

1．EMIF 接口 TMS320F28335DSP 的扩展存储器接口(EMIF)用来与大多数外围设备进行连接，典型应用 如 连接片外扩展存储器等。这一接口提供地址连线、数据连线和一组控制线。ICETEK–F28335-A 将这些扩展线引到了板上的扩展插座上供扩展使用。 2．液晶显示模块的访问、控制是由28335ADSP 对扩展接口的操作完成。 控制口的寻址：命令控制接口的地址为 0x208001，数据控制接口的地址为0x208003 和 0x208004，辅助控制接口的地址为0x208002。 3．显示控制方法： -液晶显示模块中有两片显示缓冲存储器，分别对应屏幕显示的象素，向其中写入数值将改 变显示，写入“1”则显示一点，写入“0”则不显示。(The 1.EMIF interface Extended TMS320F28335DSP memory interface (EMIF) is used to connect with the most peripheral equipment, typical application Such as The connecting piece of extended memory. This interface provides the address lines, data lines and a set of control line. ICETEK- F28335-A The extension line to the extension socket for plate on the expansion of the use of. 2 liquid crystal display module access, control by the 28335ADSP to the extended interface operation is complete. Addressing control port: Command and control interface address 0x208001, the address data control interface for 0x208003 and 0x208004, auxiliary control interface address for 0x208002. 3 display control method: - liquid crystal display module with two display buffer memory, respectively corresponding screen pixel, writing values will be changed to the Change display, write "1" shows a little, write "0" are not displayed.)