impulse

单片机DS18B20测温功能模块　DS18B20数字温度传感器接线方便，封装成后可应用于多种场合，如管道式，螺纹式，磁铁吸附式，不锈钢封装式，型号多种多样，有LTM8877，LTM8874等等。主要根据应用场合的不同而改变其外观。封装后的DS18B20可用于电缆沟测温，高炉水循环测温，锅炉测温，机房测温，农业大棚测温，洁净室测温，弹药库测温等各种非极限温度场合。耐磨耐碰，体积小，使用方便，封装形式多样，适用于各种狭小空间设备数字测温和控制领域。.(DS18B20 digital temperature sensor MCU DS18B20 temperature measurement function module wiring convenience, packaged as can be applied to a variety of occasions, such as pipes, threaded, magnets, stainless steel package, a variety of models, LTM8877, LTM8874 and so on. Main changes its appearance depending on the applications. Package after the DS18B20 temperature measurement, can be used in the cable trench blast furnace water cycle temperature measurement, boiler temperature measurement, room temperature measurement, the agriculture greenhouse temperature measurement, temperature measurement of a clean room, the temperature measurement of the ammunition depot various temperature extremes occasions. Resistant to wear and touch, small size, easy to use package forms, suitable for a variety of the narrow space equipment digital temperature measurement and control field. .)

我使用的是F103VET6，软件IIC控制，改引脚配置后可方便移植。 SDL连接PB6、SDA连接PB7、CS连接高电平，SDO连接高电平的话模块的写地址为0x3A、读地址为0x3B··· ···(I use F103VET6, software IIC control, pin configuration can be easily transplanted. SDL connects PB6, SDA connects PB7, CS connects high level. SDO connects high level telephone module with write address of 0x3A and read address of 0x3B.)

坦克车体的源代码，对电子设计大赛有一定的帮助(Tank body source code, electronic design competition has certain help)

单片机内刻录程序，包含C语言和汇编语言两个版本。实现7455C5与单片机的串口通信，信息传输。(Microcontroller burning program, contains two versions of the C and assembly language. 7455C5 microcontroller serial communication, information transfer.)

STM32的I2S编程，开发板带的程序，有做I2S音频这块的同学可以看看(STM32 I2S programming, development board with the program, has done I2S audio piece classmates can look)

keil C开发环境，51单片机与cc2520通信测试程序(the a keil C development environment, 51 and cc2520 Communications test program)

说明：  004---基于stm32电压表设计(数码管显示)(Based on STM32 voltmeter design (digital tube display)

该工程主要用的是C语言，控制器是89C52编译环境是Keil uVision4，其功能是实现特定波形输出后，通过控制数字电位器MCP41010来实现波形信号的5种频率的传输。(The project mainly use the C language, the controller is the 89C52 compilation environment KEIL the uVision4, its function is to achieve a specific waveform output, to achieve transfer of the five kinds of frequency of the waveform signal by control digital potentiometer MCP41010.)

STM32F103RB USB模拟串口范例，参考官方版本，改写双缓冲+环型队列接收，改写环节队列发送。工程开发环境为COOCOX IDE。(STM32F103RB USB virtual serial port example, refer to the official version, rewritten double buffering+ ring queue receiver, rewritten ring queue to send. Development environment for COOCOX IDE.)

使用51单片机连接BH1750光照传感器与ds18b20温度传感器，对光照、温度进行采集，通过串口打印出来(The BH1750 light sensor and DS18B20 temperature sensor are connected by 51 single chip computer. The light and temperature are collected and printed through serial port.)