EKF

迪杰斯特拉算法的matlab源文件。输出最短距离及路劲

说明：  预测控制算法中的广义预测控制编程仿真应用(Predictive control algorithm in the generalized predictive control simulation application programming)

以正弦波信号为例，对其进行信源编码、信源译码译码以及循环信道编码(a sinusoidal signal as an example, its source code, source decoder decoding and channel coding cycle)

matlab codes for e-book: Stark 2005 Wavelets and Signal Processing

故障突变量计算 12point滤序,需改为根据N自动确定滤序公式 设置故障突变量单相定值 设置故障突变量相间定值 设置故障突变量负序零序电流定值( Fault calculation 12point mutations order filter is required to determine the filter order based on the formula N automatically set the amount of single-phase fault mutation set fault value value mutation set the amount of white mutant the amount of negative sequence fault zero sequence current value)

说明：  GPS单点定位程序，kalman滤波方法，精度为20*40，有仿真分析结果图(GPS single point positioning process, kalman filter, an accuracy of 20* 40, a simulation results Figure)

《无线通信FPGA设计》这本书中所涉及的所有相关Matlab源代码(Matlab source code involved in the FPGA design of wireless communications, " This book)

详细介绍了ekf与ukf的不同及算法，对于初学者对kalma滤波很有帮助。(Details the different and algorithm of EKF and UKF, very helpful for beginners on the Kalma filter.)

PRI变换算法的基本程序，包括自相关算法，原始变换算法，改进PRI变换算法(PRI transform algorithm procedures, including autocorrelation algorithm, the original transform algorithm to improve the PRI transform algorithm)

首先,概述了太阳能光伏发电系统的组成,介绍了目前我国太阳能光伏发电技术的应用,并根据不同场合的需要,对太阳能光伏发电系统进行了分类。其次,分析了太阳能电池板的工作原理,利用州哄JLAB仿真软件对不同环境及 不同日照强度下的太阳能电池输出特性进行了建模!仿真结果证明了太阳能电池的非线性。再次,通过比较三种常用的DC/DC变换器的工作原理,提出利用BOOST型DqDC变换器实现转换,对参数进行分析后建立了BOOST型DC/DC变换器的仿真模型。最后,分析了最大功率点跟踪原理,比较了几种常用的最大功率点跟踪方法, 并在此基础上提出了一种新的扰动观察法,仿真结果表明了此方法的可行性。 (First, an overview of the composition of the solar photovoltaic power generation system, introduced the application of solar photovoltaic technology at present, and according to the needs of different occasions, for the solar photovoltaic system are classified. Secondly, the working principle of solar panels, the use of state coax JLAB simulation software for solar cell output characteristics of the different environments and under different sunlight intensity were modeled! Simulation results show that the nonlinear solar cells. Again, by comparing three common DC/DC converter works proposed use BOOST type DqDC converter to achieve the conversion, after the analysis of the parameters, the simulation model BOOST type DC/DC converter. Finally, the principle of maximum power point tracking, comparing several commonly used method for maximum power point tracking, and on this basis, we propose a new disturbance observation, simulation results show the feasibility of this method.)