k-epso

计算LTE物理层中Turbo码的误码率，该模块能应用于整个系统链路级仿真(Calculate the the Turbo code error rate in the LTE physical layer, the module can be applied to the link-level simulation of the entire system)

1 chaos_draw_GCM.m 基于最大标准差绘制的大域耦合相图（GCM）；2 chaos_GCM.m 特定参数下的大域耦合状态变量的值的时域及频域图； 3 chaos_simple.m 混沌对初始条件敏感的实验； 4 ICAS.m ICAS系统的评价数据处理； 5 julia.m 朱莉娅集的绘制； 6 logistic.m 逻辑斯蒂克集的稳定点关于参数u的分布(1 chaos_draw_GCM.m drawn based on the maximum standard deviation of the big field coupling phase diagram (GCM) big field coupling state variable 2 chaos_GCM.m special parameter values ​ ​ in the time domain and frequency domain 3 chaos_simple.m Chaos sensitive to initial conditions experimental evaluation data processing 4 ICAS.m ICAS system draw 5 julia.m Julia sets stable point 6 logistic.m logic Si Dike set of parameter distributions u)

关于matlab优化在实际生活中的一些应用(Matlab optimization on some real life applications)

平时遇到很多做MPC（模型预测控制）研究的额朋友，对MPC的学习遇到不少困难，很大的原因就是有价值的资料很少，国内尤甚。这是本极好的讲解利用Matlab对模型预测控制进行建模分析的国外书籍，书名为Model Predictive Control System Design and Implementation Using MATLAB。在这里把电子版于大家一起共享，希望对研究这块的朋友有帮助。(Usually encountered do a lot of MPC (model predictive control) study the amount of friends, learning the MPC encountered many difficulties, much of the reason is that little valuable information, domestic, especially. This excellent explanation of the use of the Matlab model predictive control modeling analysis of foreign books, the title of Model Predictive Control System Design and Implementation Using MATLAB. The electronic version in here together to share research piece of the friends.)

7自由度模型动力总成质心垂向加速度和俯仰角的功率谱密度(7 degrees of freedom model of the powertrain center of mass vertical acceleration and pitch angle of the power spectral density)

基于buck电路的滑模控制，主要包括仿真源码和文献资料等。(Sliding mode control based on buck circuit)

说明：  盲源分离(BSS: Blind Source Separation)，又称为盲信号分离，是指在信号的理论模型和源信号无法精确获知的情况下，如何从混迭信号(观测信号)中分离出各源信号的过程。盲源分离和盲辨识是盲信号处理的两大类型。盲源分离的目的是求得源信号的最佳估计，盲辨识的目的是求得传输通道的混合矩阵。(Blind source separation (BSS: Blind Source Separation), also known as blind signal separation, refers to how to separate each source signal from the aliased signal (observed signal) when the theoretical model of the signal and the source signal cannot be accurately known)

Permanent Mangnet Synchronous Motor using sliding model observer.......using SIMULINK

在最小二乘参数估计值的基础上，引进补偿项σW2C-1D Ø 0，则获得了参数的无偏估计。针对模型噪声来说，RCLS算法的适应能力比RLS更好。(In the least squares estimation parameters, on the basis of introduction of compensation term σ W2C- 1 d Ø 0, then get the parameters of the unbiased estimation. According to the model for noise, RCLS algorithm adaptive RLS better than.)

一个 天线的MATLAB 代码，是在国外的网站下的(Antenna)