single-voltage

说明：  stm32无刷电机6步启动，带霍尔传感器速度闭环(STM32 brushless motor starts in 6 steps with Hall sensor speed closed loop)

说明：  包含proteus仿真文件及c语言程序，在开发板上进行过运行。利用双色LED显示电路，和四位静态数码管显示电路模拟十字路口交通信号灯。4位LED数码管显示时间，双色LED灯显示红绿灯状态。熟悉交通信号灯控制逻辑。设计一个十字路口的交通灯控制电路，要求南北方向和东西方向两个交叉路口的车辆交替运行。每次绿灯变红灯时,要求黄灯先亮3S,才能变换运行车辆。东西方向、南北方向车道除了有红、黄、绿灯指示外，每一种灯亮的时间都用数码管显示器进行显示（采用倒计时的方法）。考虑到特殊车辆情况，设置紧急转换开头。(It contains proteus simulation file and C language program. It has been run on the development board. Two-color LED display circuit and four-bit static digital tube display circuit are used to simulate traffic lights at intersections. Four-bit LED digital tube display time, two-color LED lights show the status of traffic lights. Familiar with traffic signal control logic. Design a traffic light control circuit at the intersection, which requires the vehicles running alternately in the north-south direction and the East-West direction. Every time the green light turns red, the yellow light is required to turn on 3S before changing the running vehicle. In addition to the red, yellow and green lights in the east-west and North-South lanes, the time of each kind of light is displayed by digital tube display (countdown method). Considering the special vehicle situation, set up the emergency switch start.)

基于ARM的芯片多数为复杂的片上系统,这种复杂系统里的多数硬件模块都是可配置的,需要由软件来设置其需要的工作状态。因此在用户的应用程序之前,需要由专门的一段代码来完成对系统的初始化。(ARM-based chips, most of the complex system on chip, where the majority of this complex system can be configured hardware modules are required by the software to set up the working status of their needs. Therefore, the application before the user needs from the special section of code to complete the initialization of the system.)

红外遥控发送指令，解码模块接收后，送给数码管显示(Infrared remote control sending instruction, decoding module receives, sends the digital tube display)

使用51单片机和18B20采集温度，并用数码管显示(Use 51 And 18B20 collecting temperature and with digital display)

详细介绍了电动机如何拖动负载运行以及电动机的工作原理(Described in detail how to drag the load motor operation and motor works)

本文介绍一种利用单片机本身所提供的串行通讯口，采用自定义串行通信协议，加上总线驱动器如MAX481、MAX483、MAX485、MAX487等组合成简单的RS－485通讯网络，完成单片机间的多机通讯。(This article describes a serial communication port provided by the microcontroller itself, the custom serial communication protocols, coupled with the bus driver, such as the MAX481, MAX483, MAX485, MAX487, combined into a simple RS-485 communication network, complete single-chip between themulti-machine communication. )

单片机的计时器PWM模式实例代码，希望给相关的人员带来帮助。(Single chip timer mode PWM code examples, hope to the related personnel to bring help. )

　　　锅炉是工业过程中不可缺少的动力设备，为确保安全，稳定生产，对锅炉的自动控制十分重要。汽包水位是锅炉运行的主要指标，汽包水位过高过低都会影响运行的安全与经济性，必须严格加以控制。本文主要是用MATLAB对锅炉汽包水位控制系统进行仿真研究。建立了锅炉汽包水位对象的数学模型和控制系统，并用Matlab语言在计算机上编制锅炉汽包水位控制系统的仿真程序。通过对象特性、最佳PID参数整定、控制系统比较分析，了解了汽包水位对象特性、整定出了最佳PID参数、总结出了各种控制方案的特点与适用场合。 (　　　Boiler is a necessary power plant in the process of industry. In order to ensure the production and security, the auto-control of it is very important. The drum water level is an important variable to be controlled, it is hard to get the mathematic model of the water level with adjustive process, it is characteristic of nonlinearity, instability and time lag. The traditional control mode of three-variable in the drum water level mostly use PID.The problem of automatic control in industry coal-fired boiler is discussed in this thesis. First of all，the technological process and characteristics of industry boiler is analyzed. The task of boiler regulator is expounded. And then the system scheme of control is presented. The dynamic characteristic of loops for water level is analyzed especially the reason of ostensible water level. On the basis of these a routine PID controller is designed to control the water level. The part of differential is sensitive to high frequency noise, and easi)

单片机实验指导书和源代码，计时器/定时器，中断，键盘与显示,SPI,I2C(Instructions and source code for single-chip experiments, timer/timer, interrupt, keyboard and display, SPI, the I2C)