shuxuewulifangfa-matlab

matlab实现kalman滤波 基于无源定位的算法研究(kalman filtering matlab achieve passive location algorithm based on the research)

MATLAB命令行下mcc命令示范2 (MATLAB command line mcc orders Model 2)

用粒子群算法实现图像匹配，图像可以自己更换，建议先用matlab自带图像进行调试(Particle Swarm Optimization with image matching, image Can you change, it is recommended to use own images debug matlab)

计算圆柱绕流的程序，一个简单的matlab程序，有实时图像显示。(Calculating the flow around cylinder program, a simple matlab, a real-time image display.)

根据一个时间序列，将每个时间节点视为网络中的一个节点，两时间节点间的可视化视为边，建立复杂网络(construct a complex network according to a time series)

产生CA码的程序，利用扩频码的性质产生GOLD码，最后形成CA码(CA code generating)

本程序主要介绍了经典注水功率分配算法、迭代分块注水功率分配算法以及考虑载波泄漏功率分配算法，并对他们的吞吐量做出了相应的比较。(This procedure introduces the classic water-filling power allocation algorithm, iterative sub-block water-filling power allocation algorithm and considering the carrier leakage power allocation algorithm, and their capacity to make corresponding comparison. )

三相光伏逆变并网的仿真，针对EMD方法的不足,多元数据分析的主分量分析投影，是学习PCA特征提取的很好的学习资料，FIR 底通和带通滤波器和IIR 底通和带通滤波器，分析了该信号的时域、频域、倒谱，循环谱等。( Three-phase photovoltaic inverter and network simulation, For lack of EMD, Principal component analysis of multivariate data analysis projection, Is a good learning materials to learn PCA feature extraction, Bottom-pass and band-pass FIR and IIR filter bottom pass and band-pass filter, Analysis of the signal time domain, frequency domain, cepstrum, cyclic spectrum, etc.)

某工业系统可等效为二阶环节带延迟...且执行机构具有0.07的死区和0.7的饱和区。采样时间T=0.01；系统的输入r(t)=1.5 要求1）设计一模糊控制器，使系统输出尽快跟随系统输入；2）模糊控制与PID控制的性能进行比较；3）系统有无延迟性能进行比较(An industrial system can be equivalent to second-order part of the implementing agencies with a delay ... and the dead with a .07 and 0.7 saturation. Sampling time T = 0.01 the system input r (t) = 1.5 requirement 1) design a fuzzy controller, the system output as soon as possible to follow the system input 2) fuzzy control and PID control performance comparison 3) whether the delay in the system performance comparison)

说明：  采用matlab对两组离散点进行拟合，并在同一X轴不同Y轴（两个坐标轴中）画出拟合后的曲线，以及离散在两个y轴的单个点，在matlab中运行一次之后，将坐标轴切换到第二个y轴再次点运行即可，站长我想下modal-analysis，和examples请批准吧(Using matlab to fit the discrete points on the two groups, and different at the same X-axis Y-axis (two axes in) draw the curve fitting, and the y-axis in two discrete single point in time to run matlab After the switch to the second axis y-axis points can be run again, I think the next chief modal-analysis, and examples, please approve it)