UnderwaterCommunicationModel

说明：  离散系统的差分方程，该程序可以得出差分方程！结果挺好的！(equation)

1．通过实验加深对快速傅立叶变换（FFT）基本原理的理解。 2．了解FFT点数与频谱分辨率的关系，以及两种加长序列FFT与原序列FFT的关系。 离散傅里叶变换（DFT）和卷积是信号处理中两个最基本也是最常用的运算，它们涉及到信号与系统的分析与综合这一广泛的信号处理领域。实际上卷积与DFT之间有着互通的联系：卷积可化为DFT来实现，其它的许多算法，如相关、滤波和谱估计等都可化为DFT来实现，DFT也可化为卷积来实现。(1. Deepen the experimental fast Fourier transform (FFT) the basic tenets of understanding. 2. Understand the FFT spectrum and points of the resolution, and two extended sequence with the original FFT FFT relations. Discrete Fourier Transform (DFT) and the convolution of two signal processing is the most commonly used basic arithmetic, they relate to the signal and system analysis and synthesis of the wide range of signal processing field. DFT actually convolution and interoperability between contact : DFT into convolution can be achieved in many other algorithms, If relevant, filtering and spectral estimation could be achieved as DFT, DFT into convolution can be achieved.)

UCI 上面的经典数据 UCI 上面的经典数据UCI 上面的经典数据(UCI data)

BPSK调制在瑞利信道下的性能仿真分析，可运行(BPSK and rayleigh)

一个角度变换程序，在处理图像时，能够对图像中某一目标进行角度变换(A point of transformation process, in dealing with image, able to image targets in terms of a transformation)

un controller MCC MOTOR IN MATLAB LANGAGE

matlab基础及应用教程，详细介绍了其语言基础，数值符号运算及程序设计。(basic and applied matlab tutorial, detailing the basis of their language, numerical computation and symbolic programming.)

NP是美国匹兹堡大学的T.L.Saaty 教授于1996年提出了一种适应非独立的递阶层次结构的决策方法，它是在网络分析法（AHP）基础上发展而形成的一种新的实用决策方法。其关键步骤有以下几个： 1 确定因素，并建立网络层和控制层模型。 2 创建比较矩阵。 3 按照指标类型针对每列进行规范化。 4 求出每个比较矩阵的最大特征值和对应的特征向量。 5 一致性检验。如果不满足，则调整相应的比较矩阵中的元素。 6 将各个特征向量单位化(归一化)，组成判断矩阵。 7 将控制层的判断矩阵和网络层的判断矩阵相乘，得到加权超矩阵。 8 将加权超矩阵单位化(归一化)，求其K次幂收敛时的矩阵。其中第j列就是网络层中各元素对于元素j的极限排序向量。 (NP is a professor at the University of Pittsburgh TLSaaty presented in 1996, an adaptation of non-independent Hierarchy of decision-making method, which is the analytic network process (AHP) formed on the basis of the development of a new and practical decision-making method . The key steps are the following: A determining factor, and a network layer and control layer model. 2 create a comparison matrix. For each of the three types of indicators in accordance with normalized columns. 4 find the maximum for each comparison matrix eigenvalue and the corresponding eigenvectors. 5 consistency test. If not satisfied, then the comparison to adjust the corresponding matrix elements. 6 will each feature vector units of (normalized), to determine the composition of matrix. 7 to determine the control layer and network layer to determine matrix matrix multiplication, to be weighted super-matrix. 8 of the weighted super-matrix units of (normalized), seeking the powe)

此文档具体说明了如何设计二进制psk通信系统以及使用相关软件进行仿真(design of communication system)

Model of a DC-DC converter