登录
首页 » matlab » Cone-effect-in-MATLAB

Cone-effect-in-MATLAB

于 2013-02-24 发布 文件大小:203KB
0 213
下载积分: 1 下载次数: 5

代码说明:

  CLONE EFFECT SOURCE CODE IN MATLAB

下载说明:请别用迅雷下载,失败请重下,重下不扣分!

发表评论

0 个回复

  • f1
    说明:  差分进化算法,是一种新兴起的智能计算方法.它能求解各种无约束优化问题.(Differential evolution algorithm, is a new emerging intelligent methods of calculation. It can to solve a variety of unconstrained optimization problems.)
    2008-01-25 09:49:12下载
    积分:1
  • IIR
    IIR滤波器的设计及其使用,可产生幅度相同的单频信号,其中进行了傅里叶变换等。(IIR filter design and its use, may have the same single-frequency signal amplitude, which carried out the Fourier transform.)
    2011-04-24 13:51:51下载
    积分:1
  • zhuanju
    经典异步电机直接转矩控制,的simulink仿真(Classic direct torque control induction motor, the simulink simulation )
    2011-06-05 17:11:46下载
    积分:1
  • corrosions
    形态学的膨胀,腐蚀,细化的MATLAB的源代码,对初学者有用(Morphological expansion, corrosion, thinning of MATLAB source code, useful for beginners)
    2015-04-02 19:39:39下载
    积分:1
  • matlabh
    some exercices with matlab
    2013-12-23 18:33:13下载
    积分:1
  • SELF-TES
    matlab 专业设计 源于课本的原文件 适合于编程人员(matlab professional design textbooks from the original document is suitable for programmers)
    2007-08-12 10:55:03下载
    积分:1
  • overlap
    可视化matlab程序,经过原作者改进版本!(Matlab visualization process, after the author to improve the version!)
    2009-04-09 15:28:18下载
    积分:1
  • PolarLab
    its a nice toolbox for compressive sensing
    2013-07-11 20:12:35下载
    积分:1
  • BCH_HDL_ENCODER
    Syntetizable source code of VHDL BCH(1023,1013) encoder. This scheme used by DTMB standart and produce ten redundancy bit on 125 cycles because bus width of 8 bits.
    2010-05-12 21:28:23下载
    积分:1
  • Boost_Converter
    说明:  升压转换器是一种DC / DC电源转换器,可将电压从其输入(源)升至其输出(负载)。在连续导通模式下(流经电感的电流永远不会降为零),升压转换器的理论传递函数为: 占空比在哪里0.5 在此示例中,转换器从250 V电源馈送RC负载,并且PWM频率设置为31 kHz。 模拟 运行仿真并观察示波器上的波形。确认负载电压(Vout)的平均值非常接近理论值:Vout = 250 /(1- 0.5)= 500V。(A boost converter is a DC/DC power converter which steps up voltage from its input (source) to its output (load). In continuous conduction mode (current through the inductor never falls to zero), the theoretical transfer function of the boost converter is: where is the duty cycle.0.5 In this example, the converter is feeding an RC load from a 250 V source and the PWM frequency is set to 31 kHz. Simulation Run the simulation and observe waveforms on Scope. Verify that the mean value of the load voltage (Vout) is very close to the theoretical value of: Vout = 250 / (1 - 0.5) = 500 V.)
    2020-03-22 20:41:56下载
    积分:1
  • 696516资源总数
  • 106914会员总数
  • 0今日下载