examples

讲述了matlab作图的各种方法和情况,适合用matlab工具的所有工程技术人员以及学生老师.(Tells matlab mapping methods and conditions for use of matlab tools for students of all engineering and technical personnel and teachers.)

music算法过估计时的情况,角度精度分析(music algorithm than the estimates, angle precision analysis)

Statement and form of MATLAB in the probability distribution on the common density function

轴承外环故障诊断，故障设置为外环局部剥落，故障特征频率为外环通过频率或倍频理论计算得到475.6Hz.(Bearing outer ring fault diagnosis, fault set to the outer ring local spalling, the failure characteristic frequency for the outer ring through the frequency or frequency theoretical calculations 475.6Hz.)

现代通信系统（matlab版）（第二版）配套源代码 John G. Proakis等著 刘树棠 译 电子工业出版社出版(modern communication system (Matlab version) (2nd Edition) source code supporting John G. Proak Liushutang is waiting for the translation of the electronics industry published)

Neural network simple example

用SIMULINK搭建的数字滤波仿真程序，编译后而直接用在DSP上！(The digital filter structures using SIMULINK simulation program, compiled directly used in the DSP,!)

BP Alphabet learning program as data classification example

分数时延估计文档对于宽带信号, 基于移相的窄带波束形成方法会导致方向图波束指向的偏移和主波束畸变, 并且无法有效地抑制宽带干扰。该文提出了基于数字时延加抽头延迟线 (tapped delay line , TDL)结构的宽带自适应波束形成方法。 该方法采用数字时延滤波单元补偿宽带信号在波束指向上的相位和包络偏移, 并用基于TDL 的空时二维滤波处理抑制宽带干扰。分析和实验结果表明, 该方法可以有效地合成空间宽带波束并抑制宽带干扰, 提高信干噪比(sig nal-to-interference-plus-noise r atio , SINR)增益。(frac delay estimation)

本设计主要对4PSK调制方式的信号，利用MATLAB的m文件进行最佳接收机的设计与仿真。对输入的叠加噪声的4PSK调制信号进行接收，利用相关解调器来实现信号解调，及最大似然准则来实现检测器。在相关解调器中，接收信号分别与基函数 和 相乘再积分。在检测器中，利用相位来判断输出，从而最终得到接收的数据。采用随机二进制数通过4PSK调制后叠加高斯白噪声再对设计的接收机进行测试，从测试的结果可看出，在信噪比大于-8dB时，误码率为0，说明该接收机较好的实现了抗噪声性能。(The design of the main 4PSK modulation mode of the signal, the use of MATLAB m file for the best receiver design and simulation. The 4PSK modulated signal of the input superimposed noise is received, and the demodulator is realized by the relevant demodulator, and the maximum likelihood criterion is used to realize the detector. In the associated demodulator, the received signal is multiplied by the basis function and multiplied by the basis function. In the detector, the output is judged by the phase, and finally the received data is obtained. Using the random binary number through 4PSK modulation after the superposition of white noise and then the design of the receiver to test the test results can be seen in the signal to noise ratio greater than-8dB, the bit error rate is 0, indicating that the receiver is better The realization of the anti-noise performance.)