El-Algoritmo-MF

这是一个matlab编写的CRC冗余校验编解码程序，里面采用了美国通用的16位CRC交验多项式，(This is a matlab prepared codec CRC redundancy check procedure, which uses the U.S. General inspection of the 16-bit CRC polynomial,)

说明：  深度学习的工具箱，里面有卷积神经网络等的一些代码(Deep learning toolbox, which contains some codes such as convolutional neural network.)

MatLab+CDMA+Reference+Blockset+for+Use+with+Simulink matlab仿真(MatLab CDMA Reference Blockset for Use wit h Matlab Simulink simulation)

matlab对一幅图像，采用半径值为20、80、200的截止频率进行理想低通滤波，观察其结果。要求给出原图像及相应的付利叶频谱图和滤波结果(For an image, using the radius value of the cutoff frequency 20,80,200 ideal low-pass filter to observe the results. Required to give the original image and the corresponding Fourier spectrum and filtering results)

通过matlab的模糊工具箱，编写了倒立摆关于角度、速度的模糊pid控制，实现了对倒立摆的速度，角度的控制。(Through matlab fuzzy toolbox, written on inverted pendulum angle, speed fuzzy pid control, the realization of inverted pendulum speed, angle control.)

Software that performs Level Set based segmentation based on the Geodesic Active Contours model

matlab GUI 下简单的图书管理系统的小程序，包含有软件设计概要及用户手册，适合初学者入门。(matlab GUI for beginner)

一连续平稳的随机信号x(t)，自相关函数RX(t)=e-/t/，信号x(t)为加性噪声所干扰，噪声是白噪声，测量值的离散值Z(k)为已知，TS=0.02s。 -3.2，-0.8，-14，-16，-17，-18，-3.3，-2.4， -18，-0.3，-0.4，-0.8，-19，-2.0，-1.2，-11，-14，-0.9，0.8，10，0.2，0.5，-0.5，2.4，-0.5，0.5，-13，0.5，10，-12，0.5，-0.6，-15，-0.7，15，0.5，-0.7，-2.0，-19，-17，-11，-14。 自编卡尔曼滤波递推程序，估计信号x(t)的波形。(A continuous stationary random signal x (t), the autocorrelation function RX (t) = e-/ t /, the signal x (t) is additive noise of the interference, noise is white noise, the measured value of the discrete values ​ ​ Z (k ) are known, TS = 0.02s. -3.2,-0.8,-14,-16,-17,-18,-3.3,-2.4,-18,-0.3,-0.4,-0.8,-19,-2.0,-1.2,-11,-14 ,-0.9,0.8,10,0.2,0.5,-0.5,2.4,-0.5,0.5,-13,0.5,10,-12,0.5,-0.6,-15,-0.7,15,0.5,-0.7,-2.0,-19,-17,-11,-14. Self Kalman filter recursive procedure, the estimated signal x (t) waveform.)

数字视频技术的实验,关于穷尽块匹配算法的matlab程序及实验报告(Digital video technology experiments, exhaustive block matching algorithm matlab procedures and lab report)

给出了简单的点到点CDMA系统的物理层和链路层联合仿真的Matlab程序。程序不长，但麻雀虽小，五脏据全。有详细的中文注释，相信一看就懂。(is a simple point-to-point system CDMA physical layer and link layer joint Matlab simulation procedures. Procedures are not long, but Sparrow Although small, but it was full. A detailed notes in Chinese, I believe one can understand it.)