位同步源代码bitsynchronization

给出了BPSKMSKQAMGMSK的详细代码，可以直接在MATLAB中运行，并且有误码率的仿真。(BPSKMSKQAMGMSK given a detailed code, can be run directly in MATLAB, and BER simulation.)

本程序是用于PC与使用EtherNet/IP通讯协议的PLC进行通讯，采用C#语言编写。(This program is used for PC and the use of EtherNet/IP communication protocol PLC communication, using C# language.)

average.m为平均功率对信道容量的影响 WaterFilling.m为注水算法对信道容量的影响 主程序为天线相关性对MIMO的影响模拟(average.m average power of channel capacity WaterFilling.m channel capacity for the water-filling algorithm main program for the impact of antenna correlation on MIMO simulation)

说明：  在实际的调谐解调电路中，采用的是非相干载波解调，本振信号与发射端的载波信号存在频率偏差和相位抖动，因而解调出来的模拟I、Q基带信号是带有载波误差的信号。这样的模拟基带信号即使采用定时准确的时钟进行取样判决，得到的数字信号也不是原来发射端的调制信号，误差的积累将导致抽样判决后的误码率增大，因此数字QPSK解调电路要对载波误差进行补偿，减少非相干载波解调带来的影响。(In the actual tuning and demodulating circuit, non-coherent carrier demodulation is adopted, and the frequency deviation and phase jitter of the local oscillator signal and the carrier signal of the transmitting end are present, and thus the demodulated analog I and Q baseband signals are signals with carrier error.)

HT16C22显示驱动程序，使用I2C功能(HT16C22 display driver, using the I2C function)

RFM 70 radio Transever 2.4GHz

First, when the inter-user distance d is small, the SNR for D2D communication is high, and hence there are sufficient number of bits for high quality CSI exchange.

使用matlab进行毫米波信道模型仿真，很棒的源码(Millimeter-wave channel model simulation using matlab, great source code)

这是一个matlab和optisystem联合调试用的误码率计算程序，里面的文件报过一个可以用optisystem7和optisystem13可以打开的OSD仿真图，还有一个MATLAB计算BER的程序。给出了如何设置系统的大纲。从OptiSystem的电信号输入到Matlab组件。当OptiSystem运行时，它将调用Matlab组件中的M文件，处理数据，然后将所得的电信号导出回OptiSystem。然后将输出信号连接到BER分析仪。经过我调试，文件齐全，放心下载(The attached image gives an outline of how the system should be setup. You should start with inputting the electrical signal from OptiSystem into a Matlab component. When OptiSystem runs, it will call the M-file in the Matlab component, process the data, and then export the resulting electrical signal back into OptiSystem.The output signal is then connected to the BER Analyzer.)

数字通信中的DBPSK调制解调的原理和过程, 通过用Matlab 对这一过程的编程,分析信号在理想信道和加噪信道中传输时的(The principle and process of DBPSK modulation and demodulation in digital communication are analyzed. By programming this process with Matlab, the transmission of signal in ideal channel and noised channel is analyzed.)