path

本演示实现了主动轮廓模型由Kass等人提出。 要运行它的图形用户界面 1。基于MATLAB型引导提示。 2。关于“到现有的图形用户界面，点击” 3。选择在与本文件相同的目录snk.fig文件 4。按一下上方的绿色箭头启动图形界面 一旦GUI已经启动，您可以通过使用蛇 1。点击“新形象”，并加载输入图像。提供的样品图像。 2。平滑参数设置“西格玛”或保留其默认值并点击“过滤器”。这将平滑图像。 3。只要你点击“过滤器”，头发会出现交叉，用他们和你左击鼠标，您可以选择在图像上的初始轮廓的位置。会出现一个红色圆圈到处您单击并在多数情况下，你应该单击对象周围的一切你想要的部分。最后一点，必须挑选使用右键单击，以阻止更多的积分为MATLAB的要求。 4。设置各种蛇参数（在能源方面的相对权重的蛇目标函数）或离开它们的默认值，然后按一下他们“迭代”按钮。蛇会出现和移动，因为它收敛到它的低能量状态。(This demo implements the Active Contour Models as proposed by Kass et al. To run it with GUI 1. Type guide on the matlab prompt. 2. Click on "Go to Existing GUI" 3. Select the snk.fig file in the same directory as this file 4. Click the green arrow at the top to launch the GUI Once the GUI has been launched, you can use snakes by 1. Click on "New Image" and load an input image. Samples image are provided. 2. Set the smoothing parameter "sigma" or leave it at its default value and click "Filter". This will smooth the image. 3. As soon as you click "Filter", cross hairs would appear and using them and left click of you mouse you can pick initial contour location on the image. A red circle would appear everywhere you click and in most cases you should click all the way around the object you want to segment. The last point must be picked using a right-click in order to stop matlab for asking for more points. 4. Set the various snake paramete)

RA准则下的OFDM自适应资源分配问题，涉及载波和功率的分配，是一个既含有离散决策变量，又含有连续决策变量的非线性优化模型，且含有较为复杂的非线性约束，因此适合采用智能优化算法进行求解。(RA OFDM under guideline adaptive resource allocation problem, involving carrier and power allocation is a decision with both a discrete variable, but also with continuous decision variables of nonlinear optimization models, and contains more complex nonlinear constraints, so for using intelligent optimization algorithm.)

Robot Toolbox for simulation Robotic manipulators and Design Controller for robots

北航 张志涌的精通matlab6.5电子版。 关于matlab的基本功能使用和介绍，对于初学matlab的人是一本推荐书籍。(the book is about matlab.)

I have to write a Navier-Stokes solver for a 2-D Lid Driven Cavity. My teacher gave me a portion of his code (the Poisson pressure solver and some I.C. s and B.C. s) and I have to fill in the blanks. I ve been using

基于SVPWM的三电平逆变的matlab仿真，DC-DC部分采用定功率单环控制，多抽样率信号处理，pwm整流器的建模仿真，实现串口的数据采集，进行波形数据分析。( Based on SVPWM three-level inverter matlab simulation, DC-DC power single-part set-loop control, Multirate signal processing, Modeling and simulation pwm rectifier Achieve serial data acquisition, Waveform data analysis.)

jpeg encoder program

一本非常有价值的MAtlab编程参考书，值得一看。(A very valuable reference book MAtlab programming, worth a visit.)

这个文档采用BPSK超宽带系统。接收器是一个相关接收机具有集成低通滤波器和比较器的门限的选择(This m file models an UWB system using BPSK. The receiver is a correlation receiver with a LPF integrator and comparators for threshhold selection)

MATLAB CODE FOR IMAGE PROCESSING