bridge-spectra

file dll very important to run spike undefr matlab code.

matlab编写的模拟立方结构的磁性材料居里温度的程序，程序原理基于issing模型(the program could be used to simulate the curie temperature of cubic structured magnetic material,and the program is based on the issing model)

Simulink files: · HeaterTest.mdl Heater test model in Simulink(Requires HdataM) · TSKHeater.mdl Heater control using TSK alg(Requires HdataM,HdataF,HdataTd) · MamdaniTest.mdl Simple Mamdani test model(Requires Mdata) · Mamdani9Test.mdl 9 rule Mamdani test model(Requires Mdata) · Mamdani25Test.mdl" 25 rule Mamdani test model(Requires Mdata25) · EngineTest.mdl Vehicle engine test model in Simulink(Requires VdataM,VdataC) · MamdaniVehicle.mdl Vehicle control via simple Mamdani FLC(Requires VdataM,VdataF) · Mamdani9Vehicle.mdl Vehicle control via 9 rule Mamdani FLC(Requires VdataM,VdataF) · Mamdani25Vehicle.mdl Vehicle control via 25 rule Mamdani FLC(Requires VdataM,VdataF25) · OptimalVehicle.mdl Vehicle control via simple LQ alg(Requires VdataM,VdataC)

It will zoom the i/p image

说明：  modem.qammod对象实现M-QAM调制器，本示例中M为16。其输入参数是从0到15的整数而不是4bits二进制数据。因此，在利用此对象的modulate方法之前需要对二进制数据序列x进行预处理。特别地, 先采用MATLAB中的reshape函数将x沿着矩阵的行方向重新整理成每行4bit数据，然后应用bi2de函数将4bit数据转换成相应的整数。(modem.qammod object implements M-QAM modulator M in this example is 16. Input parameter is an integer from 0 to 15 instead of 4bits binary data. Therefore, before using the method of this object needs to modulate the binary data sequence x pretreatment. In particular, the first use of MATLAB reshape function x 4bit rearranged into each row of data in the row direction of the matrix, and then apply bi2de 4bit function to convert the data into the corresponding integer.)

实现微分方程向前查分 （教材为微分方程数值解，习题5.2.4）(forward difference)

本程序是利用ESPRIT 算法实现波达方向的估计，程序能直接运行，有一定的参考价值。。(This program is the use of ESPRIT DOA estimation algorithm, the program can be run directly, there is a certain reference value. .)

移动通信中的多用户检测算法的实现与比较，很实用的matlab程序(Mobile Communications in the realization of multi-user detection algorithm and comparison, it is useful matlab program)

本文介绍了基于MATLAB软件在《信号与系统》课程教学中的仿真实验,通过抽样信号的表征、周期方波信号的傅立叶级数分解与合成、余弦信号的相加与相乘、RLC带通滤波器的频率特性等仿真实验,说明了将MATLAB应用于教学实践中的重要作用和意义。(This article describes the MATLAB-based software in the " Signals and Systems" course teaching simulation, by sampling the signal characterization, cycle square wave signal of the Fourier series decomposition and synthesis, and the sum of cosine signal is multiplied, RLC bandpass filter the frequency characteristics simulation, MATLAB used to illustrate the important role of teaching practice and significance.)

CDMA信号调制解调，采用直接序列扩频，过加性高斯白噪声下的误码率计算。(the model of CDMA)