登录
首页 » matlab » cardiod

cardiod

于 2012-07-17 发布 文件大小:10KB
0 233
下载积分: 1 下载次数: 4

代码说明:

  this program determines the area of a cardiod using monte carlo simulation. its very helpful

下载说明:请别用迅雷下载,失败请重下,重下不扣分!

发表评论

0 个回复

  • Dijkstra
    迪杰斯塔拉算法在matlab上的程序。数学建模可以用哦(Stara Dijkstra algorithm in matlab procedures. Oh, mathematical modeling can be used)
    2013-09-14 16:34:01下载
    积分:1
  • fft
    FFT 基2变换源程序,matlab测试与系统函数变换结果一致(Radix-2 FFT transform source code, matlab test results are consistent with the system function transformation)
    2013-12-04 15:17:40下载
    积分:1
  • matlab100
    里面有很多使用的MATLAB代码,包括图形显示和计算源代码(There are a lot of use of the MATLAB code, including the graphical display and calculation of the source code)
    2009-02-28 17:03:42下载
    积分:1
  • KNNclassifier
    KNN分类方法的MATLAB代码,可以用于数据挖掘中的K最邻近值聚类方法的实现(KNN classification of MATLAB code )
    2020-10-23 14:37:22下载
    积分:1
  • A-56731EN-0107_101028
    It is possible to confirm whether error of Automatic Phase Synchronization excess the setting value of parameter No.13437-No.13440 (Threshold for Automatic Phase Synchronization error detection signal) by this signal. The signals turn to 1 in the following case: • Error of Automatic Phase Synchronization excess threshold. The signals turn to 0 in the following cases: • Error of Automatic Phase Synchronization does not excess threshold.
    2015-01-15 18:10:24下载
    积分:1
  • FIRA
    说明:  fira 实物小车的pid调节程序,效果很好,采用积分分离的pid控制器(fira-kind car' s pid adjustment procedures are very good, pid controller with integral separation)
    2010-04-08 21:54:03下载
    积分:1
  • 7
    说明:  采用卡尔曼滤波器的PID控制。控制干扰信号与测量噪声信号幅值均为0.002的白噪声信号。采用滤波器是控制效果明显改善。 (Discrete Kalman filter for PID control)
    2011-04-03 22:19:10下载
    积分:1
  • casemdlr
    利用simulink动态仿真复杂控制系统中的串级控制系统的工作过程。(dynamic simulation using Simulink complex control system of cascade control system in the process.)
    2007-05-25 23:02:05下载
    积分:1
  • canon_piano
    play Canon with piano.
    2012-09-20 22:23:22下载
    积分:1
  • turbo
    使用MATLAB完成turbo码的编码,在给定生成多项式交织映射表和删余选择的情况下进行TURBO的编码。主程序为encederm.m,调用子程序rsc_encede.m和encode_bit.m(Turbo code using MATLAB to complete the encoding, in a given generation of polynomial mapping table and delete intertwined choice than under the TURBO code. Main program for encederm.m, call Subroutine rsc_encede.m and encode_bit.m)
    2008-05-26 23:00:30下载
    积分:1
  • 696516资源总数
  • 106914会员总数
  • 0今日下载