登录
首页 » matlab » 12234445

12234445

于 2013-01-22 发布 文件大小:938KB
0 291
下载积分: 1 下载次数: 115

代码说明:

  采用卡尔曼滤波器对系统的俯仰角、 滚转角和航向角的误差进行最优估计;设计数据融合的判别准则,并根据判据的判断结果调整卡尔曼 滤波器中的量测信息,使系统可用于小型无人机的定高自主飞行(Kalman filter system pitch angle, roll angle and yaw angle error optimal estimation design data fusion criterion, and adjust according to the criterion of judging the results of measurement in the Kalman filter, making the system set high for small UAVs autonomous flight)

文件列表:

12234445.pdf,1064516,2013-01-22

下载说明:请别用迅雷下载,失败请重下,重下不扣分!

发表评论

0 个回复

  • Soundsourcelocalizationforobotauditorysystemusingt
    基于互相关函数,采用求和广义互相关函数(summed-GCC)法用于机器人系统平台。由于采用不同的映射函数(mapping functions),GCC法在该平台下,只需三个麦克风即可进行三维定位,突破了基于TDOA法进行三维声源定位最少需4个麦克风的限制(Based on cross-correlation function, using generalized cross-correlation function sum (summed-GCC) method for the robot system platform. Because of using different mapping function (mapping functions), GCC method in the platform, the only three to three-dimensional microphone positioning, a breakthrough TDOA method based on three-dimensional sound localization will take at least four microphone restrictions)
    2009-03-06 09:30:59下载
    积分:1
  • MIMO
    MIMO系统滑模控制实例 让你更好地认识MIMO应用于滑模控制(Sliding mode control instance MIMO system allows you to apply a better understanding of MIMO Sliding Mode Control)
    2013-10-27 10:58:18下载
    积分:1
  • VoiceTest
    用于检测手机麦克风输入音量大小的DEMO(it s used to detect the volume of phones micphone)
    2013-10-02 14:45:30下载
    积分:1
  • main_OFDM
    说明:  LTE ofdm编码调制解调仿真,平台为matlab(Simulation of OFDM coded modulation and demodulation)
    2021-02-02 00:06:04下载
    积分:1
  • Phase_Modulation_and_Demodulation
    Phase Modulation and Demodulation(Phase Modulation and demodulation)
    2007-04-28 16:00:36下载
    积分:1
  • gaitrecognization
    gait recognization of a person
    2011-11-12 00:22:55下载
    积分:1
  • ldpc-min-sum
    用c语言写的ldpc码的最小和算法译码程序。(The codes are about ldpc decoding,using min-sum algorithm by c++.)
    2012-12-19 18:06:59下载
    积分:1
  • BER
    这是一个matlab和optisystem联合调试用的误码率计算程序,里面的文件报过一个可以用optisystem7和optisystem13可以打开的OSD仿真图,还有一个MATLAB计算BER的程序。给出了如何设置系统的大纲。从OptiSystem的电信号输入到Matlab组件。当OptiSystem运行时,它将调用Matlab组件中的M文件,处理数据,然后将所得的电信号导出回OptiSystem。然后将输出信号连接到BER分析仪。经过我调试,文件齐全,放心下载(The attached image gives an outline of how the system should be setup. You should start with inputting the electrical signal from OptiSystem into a Matlab component. When OptiSystem runs, it will call the M-file in the Matlab component, process the data, and then export the resulting electrical signal back into OptiSystem.The output signal is then connected to the BER Analyzer.)
    2021-03-18 15:39:20下载
    积分:1
  • LabVIEWandUSB
    说明:  利用动态链接库现LabVIEW与USB设备的数据通信(Is the use of dynamic-link library of LabVIEW and the USB data communication equipment)
    2009-08-12 16:47:22下载
    积分:1
  • wirelesscommunication
    信道估计,有mmse 和ls估计,并有解释(Channel estimation, there are MMSE and LS estimates, and there are explanations)
    2020-07-28 21:38:40下载
    积分:1
  • 696516资源总数
  • 106914会员总数
  • 0今日下载