MSP430F149tu

测脉宽，基于STC15W单片机的测试要在1.3管脚加一个脉冲然后通过OLED 屏幕显示(Pulse width measurement)

Fujitsu_Easy_Kit试用手记_从入门到精通(Fujitsu_Easy_Kit trial notes _ from entry to the master)

步进电机自适应控制中的非线形问题,智能控制方法的应用(stepper motor adaptive control of non-linear problems, intelligent application of the control method)

小护士脉搏监护仪全套系统，包括程序，电路图，波形，参考资料等，还有和PC的matlab通信部分，一应俱全。(Small nurses monitor the pulse of a full set of systems, including procedures, circuit diagrams, waveform, reference materials, as well as and the PC part of matlab communication services.)

51单片机，秒表，C语言,proteus仿真，适合初学者(51 single-chip, stopwatch, C language, proteus simulation, suitable for beginners)

说明：  msp430g2553，使用内部时钟，间隔一秒闪烁。.(msp430g2553, using an internal clock, flicker one second apart)

说明：  在此基础上，设计一种温度测量系统，能够检测温度，并通过按键调整温度的上下限值，若超过该限值，进行报警提示。该系统的硬件子电路主要用Protues仿真软件实现，具体的子电路包括：恒流源电路（TLC2543芯片）、信号放大调理电路（两线制铂电阻PT100）、单片机最小系统（AT89C51）、A/D转换电路、按键电路、显示电路、声光报警器等。该系统的软件电路以C语言为基础，在Keil中实现。最后通过软硬结合，实现电路的各种情况仿真，以此验证电路设计的正确性和合理性。(On this basis, a temperature measurement system is designed, which can detect the temperature and adjust the upper and lower limits of the temperature by pressing the key. If it exceeds the limit, an alarm will be given. The hardware sub circuit of the system is mainly realized by Proteus simulation software. The specific sub circuits include: constant current source circuit (TLC2543 chip), signal amplification and conditioning circuit (two-wire platinum resistance PT100), minimum system of single chip microcomputer (AT89C51), a / D conversion circuit, key circuit, display circuit, sound and light alarm, etc. The software circuit of the system is based on C language and implemented in keil. Finally, through the combination of hardware and software, the circuit simulation is realized to verify the correctness and rationality of the circuit design.)

采用凌阳SECE061A板，外接发光二极管来设计一个语音跑马灯，具体功能如下： 1. 采用61板播放一小段语音。 2. 用发光二极管显示声音的大小。 3. 可以扩展为让声音一直循环播放。(By Ling Yang SECE061A board, an external LED to design a voice Marquee, specific functions are as follows: 1. By 61 board plays a brief speech. 2. With a voice the size of the light-emitting diode display. 3. Could have been extended to allow the sound loop.)

基于STM32F4的四轴航拍平台。以STM32F407为控制核心，四轴飞行器为载体，辅以云台的航拍系统。硬件上由飞控电路，电源管理，通信模块，动力系统，机架，云台伺服系统组成。算法上采用简洁稳定的四元数加互补滤波作为姿态解算算法，PID作为控制器，实现飞行，云台增稳等功能(Four axis aerial platform based on STM32F4. Taking STM32F407 as the control core, the four axis flying vehicle as the carrier, and the aerial camera system with ptz. The hardware is composed of flight control circuit, power management module, communication module, power system, frame and PTZ servo system. The algorithm uses a simple and stable four yuan number plus complementary filtering as the attitude calculation algorithm, and PID is used as a controller to achieve flight, PTZ stability, and other functions)

实验2：流水灯 实验步骤 1. 启动QuartusII建立一个空白工程,保存为led_water.qpf. 2. 将test2ledwater.v、int_div.v、setup.tcl拷入工程目录。 3. 将ledwater.v、int_div.v加入工程并进行综合编译，察看编译报告。从ledwater.v、int_div.v创建符号文件led.bsf、int_div.bsf。 (Experiment 2: water lamp experiment 1. Start to create a blank project QuartusII, save for led_water.qpf 2. The test2 ledwater.v, int_div.v, setup.tcl copy into the project directory. 3. The ledwater.v, int_div.v join the project and compile a comprehensive view of compiling the report. From ledwater.v, int_div.v create a symbol file led.bsf, int_div.bsf.)