MATLAB-motor-simulation

车牌检测代码 很好的东西啊 大家一起分享 共同努力啊(It is an important file)

LQG_LTR controller for Aircraft

CDMA业务信道卷积解码实现，根据上下行信道区分生成不同码率的卷积码序列，original_sequence是原始输入序列，channel_select是信道选择参数，其中下行码率为1/2，上行信道为1/3 (CDMA business channel decoder Convolutional achieve, according to the distinction between upper and lower line to generate a different channel bit rate of the convolutional code sequence, original_sequence is the original input sequence, channel_select is channel selection parameters, which downlink bit rate of 1/2, upstream channel for the 1/3)

精细积分法 求地震反应谱 可以输入阻尼比 周期等参数(Precise Integration Method Response Spectrum)

任务： 1） 借助MATLAB画出误差性能曲面和误差性能曲面的等值曲线（参考PPT2.1第17页的两幅图）； 2） 写出最陡下降法以及LMS算法的计算公式（取 ）； 3） 用MATLAB产生方差为0.05, 均值为0白噪音S(n)，并画出某次采样得到的波形（即产生任意一个噪声随机序列）； 4） 根据 2）中的公式，并利用 3）中产生的S(n)，在 1）中的误差性能曲面的等值曲线上叠加画出采用最陡下降法以及LMS法时H(n)的在叠代过程中的轨迹曲线（参考PPT2.1第17页的右下图的曲线1和曲线2）。 5）用MATLAB计算并画出LMS法时 随时间n的变化曲线（对应S(n)的某一次的一次实现）和e(n)波形； 注意：某一次实现的结果并不能从统计的角度反映实验的结果 的正确性，为得到具有统计特性的实验结果，可用足够多次的 实验结果的平均值作为实验的结果。用MATLAB计算并画出 采用LMS法时，J(n)的100次实验结果的平均值随时间n的变 化曲线（即 生成随机噪声信号并计算结果，重复执行100次， 求平均结果）。 6）在 1）中的误差性能曲面的等值曲线上，叠加画出采用LMS法得到的100次实验中的H(n)的平均值的轨迹曲线； (Task: 1 ) Draw with MATLAB error performance surface and surface contour error performance curve ( refer PPT2.1 two chart on page 17 ) 2 ) Write the steepest descent method and the LMS algorithm formula ( take ) 3 ) Using MATLAB to generate variance of 0.05 with a mean of 0 white noise S (n), and draw a particular sampling waveform ( ie, any noise generated random sequence ) 4 ) based on 2 ) of the formula , and use 3 ) generated in S (n), in a ) the error performance curves superimposed on the surface contour plot using the steepest descent method and the LMS method when H (n) the iterative process in the trajectory curve ( refer PPT2.1 page 17 bottom right of the curves 1 and 2 ) . 5 ) using MATLAB LMS method is used calculate and draw the curve with time n (corresponding to S (n) of a first implementation of a ) and e (n) waveform Note : in a first implementation of the results are not reflected from a statistical point of view of accuracy of the experimental results ,)

输入两个正整数m和n，求其最大公约数和最小公倍数。 利用辗除法。(Enter two positive integers m, n, of seeking the common denominator and least common multiple. The use of rolling division.)

数学建模中数据的分析及描述，里面包括一些matlab程序和讲义(Mathematical modeling, data analysis and description, which includes some of the matlab program and handouts)

This is Linear Discriminant Analysis code. It is made for image processing, especially in face recognition.

DCT & HADAMARD CODE.

利用DFT实现两轮信号相位差计算，包含谐波信号污染，白噪声信号污染分析(Phase difference between two signals to achieve the use of DFT calculations, the signal containing harmonics pollution, contamination white noise signal analysis)