shuruliuwei

For this project you need a 3.7v power supply that prepared by LM317 regulator. So you need MAX232 for connect uart to pc .my AVR chip project is Mega8 that you can program on any Avr chip have 2kbyte rom. In bascom spi hardware don’t work correct, so I have to software spi ,but the software spi configure have low speed into hardware spi.

本节所给出主程序功能为51单片机从USB总线读取两个字节数据，计算两个数据的和。另外本文还给出了CH372的主端点、辅助端点之间数据上传下传的子程序，供读者参考。(The main function of this section is given as 51 microcontroller reads the two bytes of data the USB bus, two data and computing. This article also gives additional primary endpoint between the auxiliary endpoints CH372 Uploaded data transfer routines, for reference)

基于stm32的红外遥控器程序资料源码 (stm32 control)

自己动手用C语言编写的火车票订票系统，很适合C语言初学者学习和交流(Yourself C language ticket booking system, it is suitable for beginners to learn C language and communication)

28335的spwm输出，开环测试，三相spwm信号分别为epwm1~6，频率为20KHz(spwm output 28335, the open-loop test, three-phase spwm signals are epwm1 ~ 6, frequency 20KHz)

定义一个Circle类，有数据成员Radius（半径），成员函数GetArea（），计算圆的面积，构造一个Circle的对象进行测试。(caculation the area of a circle)

走马灯，包括原理图和源程序，功能齐全，运用单片机开发的代码(Lantern, including schematics and source, fully functional, use microcontroller development code)

伺服电机控制系统，02年开始积累，效果好，速度快，PI控制，经典控制，fuzzy PID，自适应控制，速度位置控制等等，欢迎大家参考。(Servo motor control system, in 2002 began to accumulate, effective, fast, PI control, classical control, fuzzy PID, adaptive control, speed position control, etc., we welcome the reference.)

xl系列单片机实验仪演示程序 LCD1602显示 步进电机控制器速度方向圈数可调 LCD1602显示 步进电机控制器速度方向圈数可调 K1－启动与停止步进电机运行 K2－设定步进电机运行圈数 （1-20圈） K3－设定步进电机转动方向 K4－设定步进电机运行速度 步进电机的转速控制分16档，数字越小，转速越快。 7.5度步进电机；周期7.5×4=30度，电机转动一圈需12个周期 资源：p1.0-p1.3接反向器74ls14，输出后接步进电机 p3.7接小喇叭提供按键音, p1.4-p1.7接端口按键：lcd1602插入实验仪(xl Series Singlechip Experiment LCD1602 demo program shows the direction of stepper motor speed controller circle shows the number of adjustable LCD1602 direction stepper motor controller lap speed of a few adjustable K1-start and stop the stepper motor running K2-setting step motor running a few laps (1-20 laps) K3-set stepper motor rotation direction of K4-setting speed of stepper motor stepper motor speed control minutes 16 stalls, the number of smaller, faster the speed. 7.5 degree stepper motor cycle of 7.5 × 4 = 30 degrees, rotating electric lap 12 cycles required resources: p1.0-p1.3 then reverse browser 74ls14, followed by stepper motor output p3.7 then provide a small speaker key tone, p1.4-p1.7 port access keys: lcd1602 insert Tester)

基于单片机和C语言的，步进电机加速减速匀速演示，希望方便大家(Based on SCM and C language, stepper motor acceleration and deceleration uniform presentation, I hope to facilitate)