-
Velocity_location_volume
说明: 气候态数据处理,计算绘制数据分析图,包括经度、纬度、速度、运输量(Calculated data analysis to draw maps, including longitude, latitude, speed, traffic volume)
- 2011-03-26 10:46:53下载
- 积分:1
-
jiemi
说明: 通过MATLAB7.1编写程序,对已知的图像进行解码操作(jiemi)
- 2010-04-29 17:47:01下载
- 积分:1
-
flc5
fuzzy logic code for temperatute process in sugar evaporator
- 2012-04-13 20:12:23下载
- 积分:1
-
advanced-optimization
introduction to optimization是一本介绍优化方法的很好的书籍,对各个行业的优化编写、MATLAB程序编写、或者优化入门具有重要的指导价值,建议通读。(introduction to optimization is a very good book describes optimization methods to optimize the preparation of various industries, MATLAB programming, or optimize entry has important guiding values recommended read.)
- 2014-11-05 00:16:27下载
- 积分:1
-
zhihuanbijiao
单相有源电力滤波器仿真系统框图,电能质量的谐波补偿(APF MATLAB )
- 2012-08-16 10:02:48下载
- 积分:1
-
matlab_pwelch_windows
采用加窗法在matlab中进行功率谱密度计算(Windows and method for power spectral density calculation in matlab)
- 2014-10-26 12:11:33下载
- 积分:1
-
MATLAB_Programming
This PPT is an introduction to matlab programing
- 2011-12-24 22:14:45下载
- 积分:1
-
三次指数平滑法
说明: 用于进行数据预测,即使数据点较少,预测的结果也比较好,适用于时间序列上的建模(It is used for data prediction, even if there are fewer data points, the predicted results are better, and it is suitable for modeling on time series)
- 2020-11-27 10:53:50下载
- 积分:1
-
matlab_pipe
给水管网优化课本中的例题。计算井水管网的汇水管的水头损失。并且有图。(calculate the head lost of pipe net .)
- 2011-05-23 10:44:52下载
- 积分:1
-
grd_test
xwch_test.m是主测试文件;biaoji.mat存放滤波器系数;xiangweicha.m用FFT计算相位差。
仿真框架为:
1.标记信号和双音信号续接作为发送信号;
2.对双音中一个频率分量的相位做偏移,再经过一个低通滤波器(引入线性相位,模拟收发不能同步测量现象)后,作为收到的信号;
3.用一个检测信号对收发信号进行相关运算;
4.画出收发信号以及相关处理后的信号。找出相关信号的那个尖点,从而推算出收发双音信号0相位点;
5. 输入0相位点位置,计算相对相位差。(xwch_test.m is the main test file biaoji.mat store filter coefficients xiangweicha.m calculated using FFT phase difference. Simulation framework: 1. Mark signals and then as a two-tone signal continued to send signals 2. On a two-tone frequency components of the phase shift to do, and then through a low pass filter (the introduction of linear phase, simulation can not simultaneously send and receive measuring the phenomenon), the as received signal 3. using a detection signal of the transceiver signal correlation operation 4. draw send and receive signals and related processed signal. Correlated signal of the cusp, which calculate the two-tone signal transceiver 0 phase point 5. Enter 0 phase point position, calculate the relative phase difference.)
- 2010-06-12 17:31:00下载
- 积分:1