登录
首页 » matlab » Krinsky

Krinsky

于 2011-08-23 发布 文件大小:22KB
0 202
下载积分: 1 下载次数: 17

代码说明:

  Krinsky Fixed Structure Automata in Cellular Automata Matlab Code

下载说明:请别用迅雷下载,失败请重下,重下不扣分!

发表评论

0 个回复

  • main
    振动信号的预处理消除趋势项(最小二乘法消除多项式.)(Pretreatment to eliminate vibration signal Trend (least squares method to eliminate polynomial.))
    2010-10-22 16:29:08下载
    积分:1
  • MosaicKit
    这是MosaicKit的matlab程序,可以用于图像融合等(This is the Matlab MosaicKit procedures can be used for image fusion, etc.)
    2007-03-13 15:46:27下载
    积分:1
  • FDTD3D
    FDTD _ 3D code in matlab main structure of 3D fdtd code
    2013-07-21 23:06:58下载
    积分:1
  • ADDC
    上线(单通)的聚类算法,它接受在每一步的单个样品,更新聚类中心,并产生新的中心,根据需要。该算法是有效的,在它生成一个单传的数据集群中心。(ADDC algorithm)
    2012-01-29 20:53:54下载
    积分:1
  • matlab
    说明:  演化算法经典教材 入门者必备 很好的 非常深(Teaching beginners classical evolutionary algorithm must be very deep well)
    2011-04-02 17:36:07下载
    积分:1
  • waveletclassification-a-models
    wavelet technique is used for fault identification
    2013-11-17 23:43:20下载
    积分:1
  • fuzzy_sugeno
    fuzzy sugeno sets in matlab
    2012-12-03 20:50:12下载
    积分:1
  • d_014_mdl
    配电网中IEEE标准节点的一个传统算例.(IEEE standard distribution grid nodes a conventional example.)
    2013-07-01 10:42:16下载
    积分:1
  • 项目4
    说明:  任务:设计一个4×2.5Gbit/s 长距离光纤传输系统,并利用OptiSystem 仿真验证。 要求: 1.采用波分复用技术,波长设置以100GHz 为间隔,频率分别为193.1THz、193.2THz、193.3THz、193.4THz,每个波长传输速率为2.5Gbit/s(NRZ),传输距离为300km。采用常规光纤,光纤损耗系数为0.25dB/km。 2.单通道光发送机最大输出功率为0dBm,光接收机的接收光功率不低于-26dBm,过载点为-10dBm。 3.可以采用EDFA 作为线路放大器,其中EDFA 的输入功率限制在-18~2dBm,最大输出功率20dBm,增益范围为13~25dB,噪声指数4.0dB。(Task: Design a 4 x 2.5 Gbit/s long-distance optical fiber transmission system, and use OptiSystem simulation to verify. Requirement: 1. Using wavelength division multiplexing technology, the wavelength is set at 100GHz intervals, with frequencies of 193.1 THz, 193.2 THz, 193.3 THz and 193.4 THz, respectively. The transmission rate of each wavelength is 2.5 Gbit/s (NRZ), and the transmission distance is 300 km. The loss coefficient of conventional optical fibers is 0.25dB/km. 2. The maximum output power of a single-channel optical transmitter is 0 dBm, and the receiving power of an optical receiver is not less than -26 dBm, and the overload point is -10 dBm. 3. EDFA can be used as line amplifier, where the input power of EDFA is limited to - 18-2dBm, the maximum output power is 20dBm, the gain range is 13-25dB, and the noise index is 4.0dB.)
    2019-05-13 09:39:41下载
    积分:1
  • Matlab prog upload
    Dear Sir, I have uploaded some neural network and DSP kind of programms. Thank You, -bibyut
    2010-12-30 02:19:50下载
    积分:1
  • 696516资源总数
  • 106914会员总数
  • 0今日下载