登录
首页 » matlab » ARMA

ARMA

于 2012-06-25 发布 文件大小:2KB
0 299
下载积分: 1 下载次数: 33

代码说明:

  ARMA模态参数识别,振动信号处理应用与研究,应用MATLAB编程实现模态参数提取研究(ARMA modal parameter identification and vibration signal processing applications and research, using MATLAB programming to achieve the modal parameter extraction of)

文件列表:

ARMA.m,3279,2012-03-13

下载说明:请别用迅雷下载,失败请重下,重下不扣分!

发表评论

0 个回复

  • synchronous-identification
    synchronous identification technique
    2013-01-15 05:37:13下载
    积分:1
  • power_Transfo3phCoreType_BH
    power_Transfo3phCoreType_BH.rar,功率电子领域matlab仿真文件,已经验证过,程序运行正常(power_Transfo3phCoreType_BH.rar, Power electronics field matlab simulation file, has already been verified, the normal operating procedures)
    2013-08-26 22:02:34下载
    积分:1
  • NIT
    matlab函数包,其中含有各种功能性函数(the matlab function package, which contains various functions function)
    2012-09-20 11:15:06下载
    积分:1
  • PMSM_WEAKFLUX
    说明:  这是一个永磁同步电机的弱磁控制程序,可控初学者学习(This is a permanent magnet synchronous motor's flux weakening control program, controlled beginners learn.)
    2018-05-15 23:27:10下载
    积分:1
  • conv_vit_qam
    Convolutional(2,1,6) Encoder and soft decision Viterbi Decoder
    2007-10-13 18:52:40下载
    积分:1
  • base
    1.分别在两个图中画出δ(n)和δ(n-2),其中-10≤n≤10,画出U(n)其中-10≤n≤10。 2.分别在两个图中画出x1(n)=cos(2π×20×0.01×n),0≤n≤10和x2(n)=(0.8)n,1≤n≤6。 3.由上一题,计算y(n)=x1(n)+x2(n),并画图。(1. Draw the figure at two δ (n) and δ (n-2), where-10 ≤ n ≤ 10, draw the U (n) where-10 ≤ n ≤ 10. 2. Respectively in the two Draw the figure x1 (n) = cos (2π × 20 × 0.01 × n), 0 ≤ n ≤ 10 and x2 (n) = (0.8) n, 1 ≤ n ≤ 6. 3. from the previous question, calculate y (n) = x1 (n)+ x2 (n), and drawing.)
    2010-11-26 16:34:06下载
    积分:1
  • pvmodel
    采用文献 太阳能电池工程用数学模型的建立 所搭建的太阳能电池模型(Journal of solar cells using a mathematical model project built by the solar cell model)
    2020-11-26 18:09:31下载
    积分:1
  • pr
    说明:  image noise identification system.. when given a noisy image,program tells us the type of noise which is present in image
    2011-12-13 17:59:29下载
    积分:1
  • intergear
    通过matlab实现齿轮的三维模拟和运动动画显示(Achieved through the gears and three-dimensional simulation matlab motion animation)
    2021-02-05 21:09:56下载
    积分:1
  • ocd_prog
    很优良的PID控制器设计仿真程序与模型,经过严格检验(Very good simulation of PID controller design procedures and models, to undergo a rigorous inspection)
    2008-05-21 16:26:43下载
    积分:1
  • 696516资源总数
  • 106914会员总数
  • 0今日下载