-
kechengsheji
基于matlab的电力系统课程设计源代码,为配网潮流计算(Matlab-based curriculum design in power system source code, for the distribution network power flow calculation)
- 2009-10-29 17:09:21下载
- 积分:1
-
ECEF_GLS
说明: 地心地固(ECEF)坐标系下,基于广义最小二乘的雷达组网空间误差配准(Radar network based on generalized least square error of registration space)
- 2011-04-02 16:27:10下载
- 积分:1
-
matlab100examples
MATLAB的100个例子,包括界面设计,图像处理等(MATLAB 100 examples, including interface design, image processing, etc
)
- 2010-11-25 21:26:40下载
- 积分:1
-
matlab(bp)
matlab神经网络应用设计,里面随有详细代码(Matlab neural network application design, which with a detailed code)
- 2006-11-10 02:09:00下载
- 积分:1
-
untitled
Matlab关于三相全控桥式整流电路的仿真模拟(Matlab simulation on fully controlled three-phase bridge rectifier circuit)
- 2014-11-30 22:15:32下载
- 积分:1
-
2
基于动态切换函数的动态滑模控制,二阶系统仿真(Dynamic sliding mode control based on dynamic switching function,The second order system simulation)
- 2013-10-11 16:27:39下载
- 积分:1
-
dtmf
这是一个实现双音多频(DTMF)通信系统的编程实例,对通信系统各个环节进行了仿真(This is a dual tone multi-frequency (DTMF) communication systems programming examples for all aspects of the communication system simulation)
- 2009-11-12 13:45:01下载
- 积分:1
-
sampling-and-reconstruction-code_matlab
1.Matlab code for periodic signal
2.Matlab code for sampling and recunstruciton
- 2012-07-29 15:44:01下载
- 积分:1
-
pro_2
用局部参数最优化方法设计一个模型参考自适应系统,可调增益的初值Kc(0)=0.2,给定值r(t)为单位阶跃信号,即r(t)=A×1(t)。
要求:
1把连续系统离散化(采样时间可取0.1)。
2编制并运行这个系统的计算机程序(注意调整B值,使系统获得较好的自适应特性)。
3记录ym、yp的曲线 记录kp×kc的曲线 记录广义输出误差e的变化曲线。
4在参数收敛后,让Kp=2变为Kp=1,重新观察Kp×Kc及e的变化曲线。
5找出在确定的B值下,使系统不稳定的A值(阶跃信号的幅值),并与用劳斯稳定判据计算的结果比较。
(With local parameter optimization method to design a model reference adaptive system, adjustable gain initial Kc (0) = 0.2, for a given value of r (t) for the unit step signal that r (t) = A × 1 ( t). Requirements: a continuous system discretization (sampling time of 0.1 preferred). 2 compiled and run the system computer program (Note B to adjust the value of the system to obtain better adaptive characteristics). 3 records ym, yp curve record kp × kc curve records generalized output error e curves. 4 parameter convergence, let Kp = 2 into the Kp = 1, re-observed Kp × Kc and e curves. B-5 to find value in determining the next, making the system unstable A value (step signal of amplitude), and using Routh stability criterion and the comparison of the results calculated.)
- 2010-09-03 14:27:08下载
- 积分:1
-
guide-toisolationcircuits
关于光耦应用的比较全面的介绍,很实用,找了很久才找到的(Optocoupler applications on a more comprehensive presentation, very practical, looking for a long time to find the)
- 2011-02-16 16:26:48下载
- 积分:1