2121212121266

说明：  关于10G 以太网设计的资料，讲解的很详细，分享给大家(The information about 10G Ethernet design is explained in detail and shared with you)

说明：  基于stm32f103单片机的程序， 通过中断控制灯，点亮一盏灯(Based on the program of STM32F103 MCU, a lamp is lit by interrupting the control lamp.)

说明：  基于秉火程序改写的传感器程序，可实现光照强度，温湿度测量(Based on the sensor program rewritten by Binghuo program, the measurement of light intensity, temperature and humidity can be realized.)

说明：  正弦波的显示 ，示波器，keil5正弦波的显示 ，用于测试波形的产生(Sine wave display, oscilloscope, keil 5 sine wave display, used to test the generation of waveforms)

1、掌握利用A/D转换和计算机资源实现示波器的设计方法。 2、设计虚拟示波器。 3、建立NI-DAQmx仿真设备，选择E系列中的NI PCI-6071E数据采集卡的仿真模块，通过DAQmx物理通道识别，产生模拟信号，然后基于LabVIEW开发平台设计实现虚拟示波器。(1, master the use of A/D conversion and the design method of the computer resources to realize the oscilloscope. 2, the design of virtual oscilloscope. 3, establishment of NI- DAQmx simulation equipment, select the NI PCI- 6071- E E series simulation module of data acquisition card via DAQmx physical channel identification, produce analog signal, and then design the virtual oscilloscope based on LabVIEW development platform.)

STM32点阵屏静态显示源码,实现基本的点阵屏显示功能(STM32 lattice screen static display source code, to achieve the basic dot matrix screen display function)

详细介绍了RDS 应用，包括例程与中文数据手册(Details of the RDS application, including routine and Chinese data sheet)

说明：  东西、南北两干道交于十字路口，各干道有一组红、绿、黄三个指示灯，指挥车辆和行人安全通行。南北方向为主干道，通行时间为35秒；东风方向为支干道，通行时间为25秒。通行时间最后3秒，绿灯灭，黄灯闪烁，黄灯闪烁完毕变更通行车道。通行时间由数字显示器显示，黄灯3秒闪烁不单另计时。 特殊情况控制通行方式控制，用按键开关K1控制主道通行，支道禁行，K2控制支道通行，主道禁行，特殊情况控制通行放行。 有紧急情况时用按键开关K3控制两道均为红灯。(The east-west and North-South arterial roads intersect at the intersection. Each arterial road has a group of red, green and yellow indicator lights to guide vehicles and pedestrians to pass safely. The north-south direction is the main road with a traffic time of 35 seconds; the east direction is the branch road with a traffic time of 25 seconds. At the last 3 seconds of the traffic time, the green light is off, the yellow light is flashing, and the yellow light is flashing to change the traffic lane. The traffic time is displayed by the digital display, and the yellow light flashes for 3 seconds, not only for another time. Under special circumstances, control the way of passage. Use key switch K1 to control the passage of main road, Branch Road, K2 to control the passage of branch road, main road and special circumstances to control the passage and release. In case of emergency, use key switch K3 to control two red lights.)

详细讲解C51单片机以及C语言各项知识点必备秘籍(Detail to explain the C51 microcontroller as well as the C language knowledge essential Cheats)

STC15单片机采集中断信号，通过SIM800C报警，SHT20采集温湿度，通过OLED显示！！(STC15 MCU acquisition interrupt signal, through SIM800C alarm, SHT20 collection temperature and humidity, through OLED display!!)