labview-producers-and-consumers

该源代码是基于车载平台上的通讯诊断协议， 能够利用LabVIEW, LabWindows?/CVI, Visual C/C++ 6.0中基于CAN的汽车诊断 兼容Windows 7/Vista/XP/2000和LabVIEW Real-Time 诊断协议:CAN (ISO 15765, OBD-II)的KWP2000 (ISO 14230)和诊断 (Diagnostics) 传输协议:ISO传输协议15765-2和Volkswagen TP 2.0 兼容的接口:NI-XNET CAN、CompactRIO CAN、USB CAN和Series 2 NI CAN (PXI、PCI、PCMCIA) KWP2000和UDS的范例, 包括一个软件ECU仿真器(The source code is based on the communication diagnosis protocol on the vehicle platform. Auto diagnosis based on C AN in LabVIEW, LabWindows (/ CVI), Visual C/C++ 6.0 Compatible with Windows 7/Vista/XP/2000 and LabVIEW Real-Time Diagnostic protocols: KWP2000 (ISO 14230) and Diagnostics of CAN (ISO 15765, OBD-II) Transport protocol: ISO transport protocol 15765-2 and Volkswagen TP 2.0 Compatible interfaces: NI-XNET CAN, CompactRIO CAN, USB CAN and Series 2 NI CAN (PXI, PCI, PCMCIA) Examples of KWP2000 and UDS, including a software ECU emulator)

基于PID控制的labview程序，适用于磁悬浮球等实验和毕业设计等用途。(pid control in labview)

基于labview编写的声音采集，多功能信号发生器，与虚拟示波器(The sound written acquisition, multi-function signal generator, and virtual oscilloscope based labview )

说明：  准备电赛时使用Labview制作的电能监控系统，分为CD主页面、采集数据、电压偏差模块、控件1、小波去躁模块、谐波检测模块六部分。是很好的参考资料。(The power monitoring system made by Labview is used to prepare electric races. It is divided into six parts: CD main page, data collection, voltage deviation module, control 1, wavelet elimination module and harmonic detection module. It's a good reference.)

基于Labview的数字滤波器与频谱分析仪 滤波器可以选择是否打开滤波器，可显示波形，可设置滤波器参数，可测量时域、频域的参数，可保存数据、图像；频谱分析仪可显示波形，可测量频域参数(Labview-based digital filter and spectrum analyzer filter can choose whether to open the filter to display the waveform, the filter parameters can be set to measure the time domain, frequency domain parameters, save the data, images spectrum analyzer display waveform, measurable frequency domain parameters)

这个包中包含各种子vi，可以完成对线阵CCDTD1304的数据采集功能(Can complete the data reading function of the line CCD)

电压采集程序设计，LabVIEW的信号采集程序设计(Voltage acquisition program design)

使用labview来采集声音及处理，三分之一倍频等(Acquisition of voice and processing)

本文介绍了如何运用lABVIEW软件进行故障诊断监测(This article describes how to use LabVIEW software to troubleshoot monitoring)

说明：  基于LabvIEw的通用自动测试系统(ATs)舍计算机，可鳊程激励、响应数据采集及uuT模块，采用MxI总线控制方式。专用信号发生器为uuT提供模拟激励信号，矩阵开关和适配器完成不同信号间切换。主控计算机执行测试程序，信号发生器发送激励信号，数据采集卡采集数据，采集数据经调理后，并与标准数据|匕较是否满足相应测试结果。(The general automatic test system (ATs) based on LabvIEw can be used as a computer to excite, respond to data acquisition and uuT module. The control mode of MxI bus is adopted. Special signal generator provides analog excitation signal for uuT, matrix switch and adapter complete switching between different signals. The main control computer executes the test program, the signal generator sends the excitation signal, the data acquisition card collects the data, after the data acquisition is adjusted, and compares with the standard data | dagger whether it meets the corresponding test results.)