polinverter

PASSIVE DEVICE IN CIRCUIT WITH MODEL

该程序可以 实现始终设计 设置时分秒 设置闹铃 等等(Always designed to achieve the minutes and seconds to set the alarm clock set)

实现matlab gui 界面的人脸检测代码，界面的调用以及设计方法(Achieve matlab gui interface face detection code, interface design method calls and)

说明：  fft快速傅立叶变换源代码 打包下载 相信对大家有一定帮助(fft Fast Fourier Transform source code package to download that will definitely help all of us)

在二进制数字调制中，当正弦载波的相位随二进制数字基带信号离散变化时，则产生二进制移相键控(2PSK)信号。 通常用已调信号载波的 0°和 180°分别表示二进制数字基带信号的 1 和 0，用matlab实现其功能。(In binary digital modulation, phase when the sine wave with the discrete binary digital baseband signal changes, then generates a binary phase shift keying (2PSK) signal. Usually expressed respectively 1 and 0 binary digital baseband signal with the modulated signal carrier of 0 ° and 180 °, to achieve its function with matlab.)

基于MATLAB的MFSK调制解调，其中解调包括相干和非相干解调(MATLAB-based MFSK modulation and demodulation, which includes coherent and non-coherent demodulation demodulation)

Engineering anna university electronics department Engineering anna university electronics department

《系统辨识与MATLAB仿真.pdf》 侯媛彬 汪梅 王立琦 本书共分8章，第1、2章为辨识的基本概念、理论基础和古典辨识方法；第3至6章为现代辨识内容，其中第3章是最小二乘参数辨识，第4章是梯度校正参数辨识，第5章是极大似然法的参数辨识方法，第6章是自适应参数辨识；第7、8章为复杂的非线性系统的智能辨识和混沌辨识，其中第7章是非线性系统的神经网络辨识；第8章是Volterra辨识方法、复杂系统的混沌现象及其辨识。从第2至7章，各章均包含开发的相应程序及其程序剖析。 (" System Identification and MATLAB simulation. Pdf" Hou Yuanbin Wang Mei Wang Liqi book is divided into eight chapters, Chapters 1 and 2 for the identification of the basic concepts, theoretical foundation and classical identification methods first 3-6 chapters of modern identification content, Chapter 3 is the least squares parameter identification, Chapter 4 is the gradient correction parameter identification, Chapter 5 is the maximum likelihood parameter identification method, Chapter 6 is an adaptive parameter identification Chapters 7 and 8 for complex Intelligent identification of nonlinear systems and chaos identification, which is in Chapter 7 of the neural network nonlinear system identification Chapter 8 is Volterra identification method, complex systems and chaos identification. From the first 2-7 chapters, each chapter contains procedures for the development of appropriate programs and their analysis.)

本程序是矩形波的产生。第零步定义了要产生的波形的所有特征参数，矩形波的持续时间WIDTH，矩形波的采样点数POINTS,载波频率为F0，这个频率的最终引入是便于使用RF频率发射波形。第一步包括产生矩形波，并将其调制到RF上，注意，产生的信号的持续时间是矩形波宽度的5倍，这样，总的采样点数就是5*POINTS。同时还应注意，如果要产生一个基带信号，必须设置T0=0.第二步是画出所产生矩形波的源代码。( This procedure is rectangle wave production. Step to produce stage defined the waveform of all characteristic parameters, the duration of the rectangle wave WIDTH, rectangle wave sampling POINTS POINTS, carrier frequency F0, this frequency for the ultimate introduction is easy to use RF frequency emission waveforms. The first step including generating rectangle wave, and modulated to RF, attention, produce the duration of the signal is five times the width of rectangle wave, so, overall sampling POINTS is 5* POINTS. Also, note that if you want to produce a baseband signals must set T0 = 0. The second step is to draw a rectangular wave generated by the source code. )

spectral residual augmented classical least square source code