ReseauNeurone

SCDMA多用户的程序代码 大家可以参考一下(SCDMA multi-user program code we can refer to)

simple hover and highlight functionality

应用 Ma t l a b ／ S i mu l i n k仿真研究了这种整流器系统的三、c参数和 P I 调节器参数对直流侧电压响应及交流侧谐波与功率因数的影响，提出了一套简单易行、规范化 的设计和参数整定方法。(Ma tlab/S i mu link simulation research of this rectifier system, c parameter and the PI regulator parameters on the response of DC voltage and AC-side harmonic and power factor, a simple, standardized design and parameter tuning.)

说明：  系统辨识与MATLAB仿真程序，是学习系统辨识很好的参考资料和参考程序(MATLAB system identification and simulation program, is a good reference for learning system identification and reference procedures)

MULTIPATH for matlab

7自由度模型动力总成质心垂向加速度和俯仰角的功率谱密度(7 degrees of freedom model of the powertrain center of mass vertical acceleration and pitch angle of the power spectral density)

自组织特征映射模型(Self-Organizing feature Map)，认为一个神经网络接受外界输入模式时，将会分为不同的区域，各区域对输入模式具有不同的响应特征，同时这一过程是自动完成的。各神经元的连接权值具有一定的分布。最邻近的神经元互相刺激，而较远的神经元则相互抑制，更远一些的则具有较弱的刺激作用。自组织特征映射法是一种无教师的聚类方法。(Self-organizing maps model (Self-Organizing feature Map), that a neural network to accept outside input mode, will be divided into different regions, the regional input modes have different response characteristics, while the process is done automatically . The connection weights of neurons with a certain distribution. Nearest neurons stimulate each other, while distant neurons are mutually inhibitory, with a further some of the weaker stimulus. Self-organizing feature map method is a clustering method without teachers.)

thresholding based on FCM

一篇非常好的国外的调制识别的文章，做调制识别的可以看看。(A very good modulation recognition of foreign articles, to do modulation recognition can look at.)

计算成组滑动的滑窗检测器的最佳门限已知: 击中数N = 128, 组宽n = 8，PF = 10¡ 6，PD = 90 假设以下条件: (a) 信号不起伏 (b) 忽略天线波束调制 1 (c) 计算PD时忽略目标区以外噪声的影响 组门限(第二门限)为K=8 滑窗的门限(第三门限)为L=16 (滑窗中包含的组数为16) 求解: 最佳的KOPT 和LOPT，对这题做了具体仿真实现。需要的朋友，一定知道很有用。(Optimal threshold calculated as group slidable window detector is known: hit number N = 128, the group width n = 8, PF = 106, PD = 90 assuming the following conditions: (a) signal is not undulation ( b) ignore the antenna beam modulation 1 (c) the calculation of PD ignored outside the target area noise of impact group door limit (the second door limit) for K = 8 sliding window of the door limit (third door limit) for L = 16 (sliding window contains group 16) to solve: the best of the KOPT the LOPT, these questions do specific simulation to achieve. A friend in need, we must know to be useful.)