Phase_Modulation_and_Demodulation

比较完整的OFDM的仿真模型和源码,有比较完整的设计思路,可供学习(Relatively complete OFDM simulation model and the source code, there is a complete design ideas, to learn from)

在理想情况下和干扰存在情况下，JP和CBF性能对比(the differencebetween JP and CBF)

这是瑞丽衰落信道模型和莱斯衰落信道模型的代码。(This is the code of Rayleigh fading channel model and Rice fading channel model)

说明：  STC单片机多机连级串口程序可实现.416路控制. 串口和485都可以使用、 一个程序可以用在26块控制板上，通过拔码开关给板子编号，每块板可以过滤分析所接收到不同的代码。进行继电器的动作，能返回数据，因使用定时器发送返回，不会阻塞或者代码错乱、可以 用在中控，物联网，等各种控制场合。修改代码后，能达到上千路的控制。(STC single-chip microcomputer multi-level serial port program can realize 416 channel control. Serial port and 485 can be used. One program can be used on 26 control boards. Each board can filter and analyze different codes received by numbering the boards with the pull-out switch. Relay operation can return data, because the timer is used to send the return, it will not block or code confusion, and can be used in central control, Internet of things, and other control occasions. After modifying the code, it can achieve thousands of control.)

说明：  Log4net.dll是著名的Apache软件为.net framework 2框架准备的支持库，方便在不同的平台上得到功能支持。(Log4net. DLL is a support library prepared by Apache software for.NET Framework 2. It is convenient to get functional support on different platforms.)

STIM300高精度IMU的输出解码程序，MOD93格式，带CRC校验，直接可以运行(MOD93 format with a CRC check can be run directly)

说明：  cpofdm信道模型仿真，通过仿真得到cpofdm信道模型的复杂度和在各种信噪比下的误码率(Through the simulation of cpofdm channel model, the complexity of cpofdm channel model and the bit error rate under various SNR are obtained)

16QAM调制信号的GAD定时恢复，对定时恢复环路的验证和实现(Gardner Timing Recovery for 16QAM)

Dopod 838官方拆机及维修手册,很详细的说明，照着他一步一步拆，很简单的，我的手机坏了就是照他拆了修的。(Dopod 838 official TBM Break-down and maintenance manual, a very detailed explanation, he told a step-by-step demolition very simple, I had a bad cell phone as he was taking off the surface.)

在MATLAB上设计一个（2，1，3）卷积编码器和对应的采用维特比译码算法的译码器。编码器的生成多项式为：[1 0 1；1 1 1]。将编码器的输出经过一个高斯白噪声信道的结果作为译码器的输入，观察比较译码器输出和编码器输入，了解卷积码的容错性，并计算译码结果的误比特率.(A convolutional coder (2, 1, 3) and corresponding decoder using Vitby decoding algorithm are designed on MATLAB. The generating polynomial of encoder is: [1 01; 11 1]. The output of the encoder through a Gauss white noise channel as a result of the decoder input, compare the output of the decoder and encoder input, understand the fault tolerance of convolutional code, and calculate the decoding results of bit error rate.)