登录
首页 » matlab » 1-1Signalpf

1-1Signalpf

于 2007-04-07 发布 文件大小:1KB
0 261
下载积分: 1 下载次数: 25

代码说明:

  Systemview是重要的通信系统仿真软件,国外用的很多。这是我做硕士阶段仿真的一些源代码,对通信系统设计开发非常有用,由于没有Systemview这个板块,所以放在这里。这是一个信号平方仿真的Systemview源代码。(Systemview is an important communication system simulation software used in many foreign countries. This is what I do Simulation Master stage some source code, the communication system design and development is very useful. Because no Systemview the plate, so on here. This is a signal of Systemview square simulation source code.)

下载说明:请别用迅雷下载,失败请重下,重下不扣分!

发表评论

0 个回复

  • 10463
    matlab 入门基本操作 包括一些基本的源代码 和实力
    2011-10-25 13:04:01下载
    积分:1
  • OpenCV2-Cookbook
    OpenCV2 ComputerVision Application Programming Cookbook英文版,适合初学者学习(OpenCV2 ComputerVision Application Programming Cookbook in English, suitable for beginners to learn)
    2015-01-03 16:13:58下载
    积分:1
  • iNemo_M1_Applications
    iNemo_M1_Applications,这款ST公司的九轴传感器,数据读取,姿态结算,融合。很全的一个工程,刚刚测试通过。(iNemo_M1_Applications, this ST s nine-axis sensor, data read, posture settlement, integration. It is full of a project, just test.)
    2015-04-27 14:53:06下载
    积分:1
  • fengun
    大学数值分析算法,与理论分析结果相比,搭建OFDM通信系统的框架。( University of numerical analysis algorithms, Compared with the results of theoretical analysis, Build a framework OFDM communication system.)
    2016-08-06 14:22:39下载
    积分:1
  • POD
    说明:  数据快照的特征提取,获得基模态、特征值和模态系数,以及数据的后处理。(Feature extraction of data snapshot, obtaining basic modes, eigenvalues and modal coefficients, and post-processing of data.)
    2021-01-22 19:08:44下载
    积分:1
  • dds
    DDS信号的产生程序,以及DDS相关文章,综合报告。(DDS signal generation procedures and the DDS articles, comprehensive reports.)
    2010-10-22 20:24:51下载
    积分:1
  • dow-jones
    prediction of dow-jones index
    2010-12-25 19:11:43下载
    积分:1
  • fitting-silver-dielectric-constant
    用MATLAB拟合复数,这是拟合银介电常数的例子!(MATLAB fitting plural,It is a example for fitting silver dielectric constant。)
    2012-04-19 13:52:20下载
    积分:1
  • velocity_filtering_based_on_make_zeta_output_0
    This code uses the output from either make_zeta_u.c file or make_zeta_v.file i.e. it uses the velocity data at any z-level specified by zlevel1. Furthermore, this code filters the velocities, plots the filtered and raw signals at certain specified locations and then creates maps of the velocity time series
    2011-06-06 11:26:54下载
    积分:1
  • PF33bus
    IEEE 33节点系统(仅PQ节点)三相不平衡潮流的前推回代算法,MATLAB中直接运行出结果。可在本程序基础上做修改,进行进一步开发。(IEEE 33-node system (only the PQ node) three-phase unbalanced trend forward and backward substitution algorithm, results run directly MATLAB.)
    2021-05-07 16:16:36下载
    积分:1
  • 696516资源总数
  • 106914会员总数
  • 0今日下载