MATLAB_interface_mannual

两单元的受力分析，可以得到应力、应变等重要的参数信息(Mechanical analysis of the two units can be important parameters of the stress, strain, etc.)

vblastpic1:tx=2,rx=2时ZF,ZF-SIC,MMSE,MMSE-SICvblastpic2:tx=4,rx=4时ZF,ZF-SIC,MMSE,MMSE-SIC vblastpic3 vblastpic4:MIMO vblastpic6:tx=4,rx=4, vblastpic7ZF-SIC(unordered) vblastpic8: vblastpic9: vblastpic10: vblastpic11:能 vblastpic12:tx=2,rx=2,MMSE-SIC , tx=2,rx=2,ML vblastpic13:tx=2,rx=2,Vblast ML检测 (QPSK调制) vblastpic14:tx=2,rx=2,ZF-PIC检测性能 vblastpic15:tx=4,rx=4,Vblast QR分解检测 vblastpic16:tx=4,rx=4,VBLAST ML检测 (QPSK调制)

说明：   在三次样条中，要寻找三次多项式，以逼近每对数据点间的曲线。在样条术语中，这些数据点称之为断点。因为，两点只能决定一条直线，而在两点间的曲线可用无限多的三次多项式近似。因此，为使结果具有唯一性。在三次样条中，增加了三次多项式的约束条件。通过限定每个三次多项式的一阶和二阶导数，使其在断点处相等，就可以较好地确定所有内部三次多项式。此外，近似多项式通过这些断点的斜率和曲率是连续的。然而，第一个和最后一个三次多项式在第一个和最后一个断点以外，没有伴随多项式。因此必须通过其它方法确定其余的约束。最常用的方法，也是函数spline所采用的方法，就是采用非扭结(not-a-knot)条件。这个条件强迫第一个和第二个三次多项式的三阶导数相等。对最后一个和倒数第二个三次多项式也做同样地处理。 (the Cubic Spline, to find three polynomial, approaching every right to point the data curve. The kind of terms, these data points called breakpoints. Because only two points a straight decisions, and in between the two curves can be used an infinite number of cubic polynomial approximation. Therefore, in order for the outcome of uniqueness. The Cubic Spline, add the cubic polynomial bound by the conditions. By limiting each cubic polynomial of the first order and second-order derivative, it breakpoint in the same Department, we can better identify all internal cubic polynomial. In addition, the polynomial approximation of these breakpoints slope and curvature is continuous. However, the last one and a cubic polynomial in a breakpoint and the final one, not accompanied by polynomials. There)

融合程序,matlab的源代码。内含两个程序。(Fusion program, Matlab source code. Contains two procedures.)

用matlab通过将txt中的数据，最终画出来一副图像，用于实验的先期和后期处理。(Matlab by comparing the data in TXT, finally draw a image, early and late processing used in the experiment. figure)

该程序用matlab编写实现对商标文字分割和识别。(the procedures used to achieve the preparation of Matlab trademark characters segmentation and recognition.)

基本遗传算法的Matlab工具包，在Matlab环境下实现。(basic genetic algorithm Matlab tool kits, under Matlab environment.)

一个关于陀螺转动的简单模拟程序,是用MATLAB编写的.(a rotating gyroscope on the simple simulation program is prepared by using MATLAB.)

这是很实用的一个matlab的录音界面小程序，经行语音录制，分析等。(This is a very useful little program matlab recording interface, the line of voice recording and analysis.)

liu超混沌系统的时序图及liu超混沌系统的相轨迹图的程序(Timing Diagram liu liu hyperchaotic system and hyperchaotic system phase trajectory program)