VcAddMATLAB

经典泊松方程的matlab数数值求解程序代码。可直接使用。 (Matlab the number of values ​ ​ of the classical Poisson equation solver code. Can be used directly.)

利用非线性控制完成光伏并网逆变器的设计，设计中采用模糊控制和反步法，介绍很好。(Using nonlinear control to complete the design of the photovoltaic (pv) grid inverter, adopted in the design of advanced reverse moves, the introduction is very good.)

vc与matlab混合编程的具体实例。vc调用matlab的.m函数，经过编译之后转换为C++程序，实现进行混合编程。(vc mixed with Matlab programming specific examples. Vc call Matlab. M function, compiled after the conversion of C procedures, mixed programming.)

ldpc的matlab实现程序，和几篇文档资料(ldpc matlab implementation procedures, and several documentation)

说明：   有一个长度为整数L(1<=L<=10000)的马路，可以想象成数轴上长度为L的一个线段，起点是坐标原点，在每个整数坐标点有一棵树，即在0,1,2，...，L共L+1个位置上有L+1棵树。 现在要移走一些树，移走的树的区间用一对数字表示，如 100 200表示移走从100到200之间（包括端点）所有的树。 可能有M(1<=M<=100)个区间，区间之间可能有重叠。现在要求移走所有区间的树之后剩下的树的个数。 输入： 两个整数L(1<=L<=10000)和M(1<=M<=100)。 接下来有M组整数，每组有一对数字。 输出： 可能有多组输入数据，对于每组输入数据，输出一个数，表示移走所有区间的树之后剩下的树的个数。(Has a length of integer L (1 &lt = L &lt = 10000) of the road, one can imagine a number line segment of length L, the starting point is the coordinate origin, each integer coordinate points in a tree, i.e. 0,1 , 2, ..., L total has L+1 L+1 positions on the tree. Now to remove some trees, tree removed by a range of digitally represented, such as 100 200 represents removed (inclusive) between 100 and 200 all the trees. There may be M (1 &lt = M &lt = 100) intervals, there may be overlap between the intervals. Now, after the number of trees require the removal of all remaining sections of the tree. Input: two integer L (1 &lt = L &lt = 10000) and M (1 &lt = M &lt = 100). Then there is an integer M groups, each with a pair of numbers. Output: there may be multiple sets of input data, for each set of input data, the output of a number indicating the number of the removal of all remaining sections of the tree after tree.)

现代通信系统第6章matlaab程序源码源码 (Chapter 6 of the modern communication systems matlaab program source code)

仿真程序：首先需要用一个随机发生器产生（0.1）内的均匀随机数，然后再将该序列映射到对应的幅度电平｛Am｝。然后将这个范围再分成4个相等的区间，这些子区间分别对应于4个信号比特的符号00，01，10，11。检测器观察到r=Am+n，并且计算r和4种可能传输的信号幅度之间的距离，它的输出Bm就是相应于最小距离的信号电平。Bm与真正的的传输信号幅度比较，差错计数器用来对检测器产生的差错计数。(Simulation program: first need to use a random generator (0.1) the uniform random number, then the sequence is mapped to the corresponding amplitude level {Am}. Then this range has been divided into four equal intervals, these sub-intervals corresponding to four signal bits of the symbol 00,01,10,11. Detector observed r = Am+ n, and calculate r and 4 possible transmission distance between the signal amplitude, its output corresponding to the minimum distance Bm is the signal level. Bm and the real rate of transmission of the signal comparison, error detection counter is used to generate the error count.)

Matlab中基于dq变换的锁相环仿真研究.(Matlab based on dq transformation of phase-locked loop simulation.)

Visual Studio 2008 下可以编译通过的CJLibary.(CJLibrary version 6.08c with Visual Studio 2008 project.)

MATLAB和c的先进PID算法测试文件，大学课程用先进PID算法。(The test file of advanced PID algorithm of MATLAB and C, university course with advanced PID algorithm.)