SDR

matlab语言编写的gardner的定时同步算法仿真程序(matlab language gardner Timing Synchronization Algorithm Simulation Program)

信道比特分配需要根据信道好坏分配，可采用自适应chow算法 MATLAB编程( U81EA u9002 u5E94chow u7B97 u6CD5 MATLAB u7F16 u7A0)

本试验是用数字基带处理方法来实现调试期算法的基带硬件实验。 通过用软件matlab进行了GMSK相位路径和眼图的仿真,之后对任何一种五位随机码，每周期八次的任一抽样时刻，和任一相位区域(0、1、2、3)的任一组合，计算出相位 ，并对 以及 进行1024位的量化、编码成10位二进制码表。进一步利用matlab从上述的码表得出GMSK基带波形的眼图，和理论上计算的眼图比较，一致性很好。(眼图主程序) (This test is a method to realize the digital baseband processor debugging phase algorithms with hardware-based experiments. By using the software matlab a GMSK phase path and the eye diagram of the simulation, after any one of five random code, eight times per cycle of any one sampling time, and any one-phase region (0,1,2,3) of any combination of one to calculate the phase, and 1024 as well as quantitative, encoded into a binary code table 10. Further use of matlab code from the above tables GMSK baseband waveform eye diagram and eye diagram theoretically compared to a good consistency. (Eye diagram of main program))

前后向平滑算法：算法的原理很简单，以五点三次平滑为例。取相邻的5个数据点，可以拟合出一条3次曲线来，然后用3次曲线上相应的位置的数据值作为滤波后结果。简单的说就是 Savitzky-Golay 滤波器 。只不过Savitzky-Golay 滤波器并不特殊考虑边界的几个数据点，而这个算法还特意把边上的几个点的数据拟合结果给推导了出来。(Before and after the smoothing algorithm: the principle of the algorithm is very simple, to 5.3 times smooth as an example. Take the adjacent five data points, you can fit out a curve 3 times, and then use the corresponding position on the third time the data value as the filtered results. Simply said is the Savitzky-Golay filter. However, the Savitzky-Golay filter does not specifically consider several data points of the boundary, and this algorithm also specifically to the edge of a few points of the data fitting results derived.)

欧洲标准DVB-S2的LDPC编码的实现代码(European standard DVB-S2 LDPC encoding implementation code)

认知无线电中，采用循环特征检测的频谱检测算法matlab仿真程序(Using cyclic feature detection spectrum detection algorithm)

To understand the transmission scheme for QPSK modulation. To design a simple transceiver structure operating in a noisy channel.

用于对基于GOLD码的串行捕获算法，可以自定义信噪比，待捕获信号参数，代码分成搜索跟踪和捕获两部分，其中搜索的步长等参数也可以自定义，代码中acquiresignal.m部分为最终捕获相位展示的主程序。(For the serial acquisition algorithm based on GOLD code, we can customize the signal-to-noise ratio and the parameters of the signal to be captured. The code is divided into search part and capture part, The parameters such as search step can also be customized. Acquiresignal.m part is the main progress to output the results of the capture of phase.)

修改的PRI变换法，用于雷达信号分选，可以处理抖动的雷达信号(PRI modified transformation method for radar signal sorting, you can deal with the radar signal jitter)

求阵列天线方向图，矩形栅格点平面阵方向图。(Array antenna pattern)