zhuangtaixiangying

this code is a faster kmeans clustering implementation

说明：  计算分子流态下气体分子通过直圆管道时的角度分布的数值解(Calculation of gas molecules under molecular flow through straight circular pipes of the angular distribution of the numerical solution)

java和matlab混合编程的一种方法(java and Matlab programming a mixed approach)

10kv配电网单相接地故障仿真模型，可实现直配线路及带分支线路的仿真，还可以直接观察到故障后电压电流信息的模分量(10kV single phase to earth fault of distribution network simulation model)

说明：  用于人工智能分类算法仿真的数据集 UCI数据集 已经过集成(Simulation of artificial intelligence classification algorithm for data sets UCI data sets have been integrated)

说明：  Remez滤波，BPSK复合基带信号仿真，载波生成器!(Designed to meet the following indicators, such as ripple linear phase FIR low-pass filter)

提出了一种新的基于小波包变换 和偏斜度的检测方法。该方法利用小波包对图像进行多尺度分解，解决了高频段分辨率低的问题； 并提出了一个基于偏斜度的高斯判别准则，用于对小波包分解系数进行高斯性检验，最终得到了 小目标的精确检测(The wavelet packets were applied to decompose the image into pyramid subbands at different scales and solve the problem of the higher frequencies having lower resolutions. Then a Gaussian measurement criterion based on skewness was proposed to test the Gaussian nature of the wavelet packet coefficients and finally the exact detection result was obtained. )

说明：  任务：设计一个4×2.5Gbit/s 长距离光纤传输系统，并利用OptiSystem 仿真验证。 要求： 1．采用波分复用技术，波长设置以100GHz 为间隔，频率分别为193.1THz、193.2THz、193.3THz、193.4THz，每个波长传输速率为2.5Gbit/s（NRZ），传输距离为300km。采用常规光纤，光纤损耗系数为0.25dB/km。 2．单通道光发送机最大输出功率为0dBm，光接收机的接收光功率不低于－26dBm，过载点为－10dBm。 3．可以采用EDFA 作为线路放大器，其中EDFA 的输入功率限制在－18～2dBm，最大输出功率20dBm，增益范围为13～25dB，噪声指数4.0dB。(Task: Design a 4 x 2.5 Gbit/s long-distance optical fiber transmission system, and use OptiSystem simulation to verify. Requirement: 1. Using wavelength division multiplexing technology, the wavelength is set at 100GHz intervals, with frequencies of 193.1 THz, 193.2 THz, 193.3 THz and 193.4 THz, respectively. The transmission rate of each wavelength is 2.5 Gbit/s (NRZ), and the transmission distance is 300 km. The loss coefficient of conventional optical fibers is 0.25dB/km. 2. The maximum output power of a single-channel optical transmitter is 0 dBm, and the receiving power of an optical receiver is not less than -26 dBm, and the overload point is -10 dBm. 3. EDFA can be used as line amplifier, where the input power of EDFA is limited to - 18-2dBm, the maximum output power is 20dBm, the gain range is 13-25dB, and the noise index is 4.0dB.)

Find edges of a color image

战场最新源代码大家一起研究一下。看看还有什么不对的地方进行最新的描述(大家一起研究一下。看看还有什么不对的地方进行最新的描述)