rayleighfadingchannelsimulationmatlabcode

典型隶属函数仿真程序 matlab仿真 (Typical membership function simulation program matlab simulation)

在转速为48K/min时，滚动体的几个时域波形(In speed for 48 k/min, rolling body several time domain waveform )

M-Z干涉仪结构有限差分光速传播法源程序(The source program of M-Z Interferometer in FD-BPM)

Simple demonstration of modeling intermodulation tones.

模拟通信系统中，幅度调制及频率调制的代码，调制与解调，应用matlab实现。(Analog communication systems, amplitude modulation and frequency modulation code, modulation and demodulation, the application of matlab.)

1、本程序用于仿真里德-穆勒（Reed-Muller）码在AWGN信道中的性能，调制采用bpsk 2、理论请参见《差错控制编码》（第二版），Shu Lin（美）编，晏坚等（译）一书P70-75.且仿真结果与书中图4-2完全一致 3、BPSK_AWGN_RM_Code.m为主程序，点击运行即可 4、The_creation_of_RM_code.m和RM_Decode.m分别为RM码的编、译码程序，而Majority_logic_decision.m用于译码中的大数判决，combine_dunction.m用于计算组合数。(1, the procedure for the simulation Reed- Muller (Reed-Muller) codes in AWGN channel performance, modulation using bpsk 2, theory, see " Error Control Coding" (second edition), Shu Lin (America) series , Yan Jian, etc. (translated) book P70-75., and the simulation results consistent with the book Figure 4-2 3, BPSK_AWGN_RM_Code.m-based program, click Run to 4, The_creation_of_RM_code.m and RM_Decode.m were RM compiled code decoding process, and in large numbers for decoding Majority_logic_decision.m judgment, combine_dunction.m used to calculate the number of combinations.)

任务： 1） 借助MATLAB画出误差性能曲面和误差性能曲面的等值曲线（参考PPT2.1第17页的两幅图）； 2） 写出最陡下降法以及LMS算法的计算公式（取 ）； 3） 用MATLAB产生方差为0.05, 均值为0白噪音S(n)，并画出某次采样得到的波形（即产生任意一个噪声随机序列）； 4） 根据 2）中的公式，并利用 3）中产生的S(n)，在 1）中的误差性能曲面的等值曲线上叠加画出采用最陡下降法以及LMS法时H(n)的在叠代过程中的轨迹曲线（参考PPT2.1第17页的右下图的曲线1和曲线2）。 5）用MATLAB计算并画出LMS法时 随时间n的变化曲线（对应S(n)的某一次的一次实现）和e(n)波形； 注意：某一次实现的结果并不能从统计的角度反映实验的结果 的正确性，为得到具有统计特性的实验结果，可用足够多次的 实验结果的平均值作为实验的结果。用MATLAB计算并画出 采用LMS法时，J(n)的100次实验结果的平均值随时间n的变 化曲线（即 生成随机噪声信号并计算结果，重复执行100次， 求平均结果）。 6）在 1）中的误差性能曲面的等值曲线上，叠加画出采用LMS法得到的100次实验中的H(n)的平均值的轨迹曲线； (Task: 1 ) Draw with MATLAB error performance surface and surface contour error performance curve ( refer PPT2.1 two chart on page 17 ) 2 ) Write the steepest descent method and the LMS algorithm formula ( take ) 3 ) Using MATLAB to generate variance of 0.05 with a mean of 0 white noise S (n), and draw a particular sampling waveform ( ie, any noise generated random sequence ) 4 ) based on 2 ) of the formula , and use 3 ) generated in S (n), in a ) the error performance curves superimposed on the surface contour plot using the steepest descent method and the LMS method when H (n) the iterative process in the trajectory curve ( refer PPT2.1 page 17 bottom right of the curves 1 and 2 ) . 5 ) using MATLAB LMS method is used calculate and draw the curve with time n (corresponding to S (n) of a first implementation of a ) and e (n) waveform Note : in a first implementation of the results are not reflected from a statistical point of view of accuracy of the experimental results ,)

matlab show FFT and so on

Alan variance method of Fiber Optic Gyroscope

another of my homework......thanks! it is about a correlation in space domain(another of my homework ... thanks! It is about a correlation in space domain )