Matlab-example

现代功率谱估计，信号与信息处理，music算法(Moderne Leistungsspektrum Schä tzung, Signal-und Informationsverarbeitung, Musik-Algorithmus)

Open Core Protocol ( OCP ) TEXAS-Instrument(Open Core Protocol ( OCP ) TEXAS-Instrument)

该方法是利用RSSI算法进行节点之间定位的一种方法。(This method is the use of RSSI between node positioning algorithm in a way.)

将实验采集的人生理信号进行处理，提取心音信号，对心音信号进行时域和频域分析(The experiments were collected physiological signal processing, extraction of heart sound signals, heart sound signals in time domain and frequency domain analysis)

MATLAB 学习指南第六章．编写与调用函数(MATLAB Learning Guide Chapter VI. Prepared with the call function)

经验模式分解算法是仿真分数阶高斯噪声(fGn)和分数阶布朗运动(fBm)的新方法， 利用MATLAB的GUI开发环境，设计和实现了基于经验模式分解的分数阶随机序列仿真系统。(Empirical mode decomposition algorithm is a simulation of fractional Gaussian noise (fGn) and fractional Brownian motion (fBm) of the new method, using MATLAB' s GUI development environment, design and implementation of empirical mode decomposition based on the fractional order random sequence simulation system.)

The study consisted of an introduction, three scans performed for each of the eleven scanners, and an adjacent interview. We utilized a within-subject design. The dependent variables were task completion time and reliability, by which we mean the share of successful scans within a task completion time below 15 seconds. The independent variables were the barcode scanners as listed in Table 1. For each participant the study was recorded on video. We also transcribed comments the participant made during the tasks.

说明：  关于Bayes分类器的 实验数据都有,下载查看内容(about Bayes, you can down it,have data and code)

说明：  对新冠肺炎病例传播数据进行清洗，并进行可视化，包含流向地图和桑基图。(The novel coronavirus pneumonia transmission data were cleaned and visualized, including flow maps and sonkey maps.)

利用ccs环境、MATLAB环境、DSP（TMS320F2812)、被测对象和Agilient网络分析仪E5071B，构建一个自动测量系统。 相信大部分人都知道基于NI公司的GPIB总线，可以实现自动测量，但NI公司的方案实在太昂贵，采用MATLAB能够大大降低成本。matlab与ccs之间基于RTDX协议进行数据交换，同时matlab基于TCP/IP协议与E5071B之间通信，源码说明如下： （1）RTDX_ok目录：matlab7.0代码，包含了一个用GUI实现的界面和相关的具体代码，特别是在其中实现了SCPI语言来对仪器进行控制。 （2）TMS320F2812目录：包含ccs下的c代码，如果没有做过RTDX的应用，相信这个对你很有启发。(Use ccs environment, MATLAB environment, DSP (TMS320F2812), the measured object and Agilient network analyzer E5071B, construct an automatic measurement system. I believe that most people are aware NI' s GPIB-based bus, you can realize automatic measurement, but NI' s program is too expensive, the use of MATLAB can greatly reduce costs. ccs between matlab and RTDX protocol-based data exchange, while matlab based on TCP/IP protocol and communication between the E5071B, the source described as follows: (1) RTDX_ok directory: matlab7.0 code, contains a GUI implementation with the interface and specific code, especially in one of implementation of the SCPI language to control the apparatus. (2) TMS320F2812 directory: contains ccs of c code, if not done RTDX application, then I think it was very instructive for you.)