white-noise

an introduction to butterworht filter

基于特征的影像匹配——SIFT Method!!! 相当经典,只不过是MatLab源码，希望有哪位高手能转换成VC++源码!(feature-based image matching-- physiology Method! ! ! Quite classic, MatLab is the only source, which experts hope will be converted into VC source!)

ant colony for TSP problem

说明：  异步电机的精确控制和速度辨识是交流传动系统中重要问题。该仿真模型在异步电机的数学模型、矢量控制原理及速度辨识算法的基础上，利用Matlab/Simulink仿真软件中SimPowerSystems模块，构建了基于MRAS无速度传感器的异步电机矢量控制系统。(The precise control and the speed identification of AC motor are the very important issues on AC drive system. In this paper, on the basis of analyzing the mathematical model of AC motor, the principle of vector control and the algorithm speed identification, the speed sensorless vector control system of induction motor based on MRAS is constructed on SimPowerSystems modules of Matlab/Simulink simulation software. )

利用离散小波对图像进行压缩的matlab源程序(Use of discrete wavelet image compression matlab source)

It is Radar System design and signal prcessing code based on standard algorithm .this is vey important for biggener those who are working on Radar signal processing area.This code contain various chapter. this is basically chapter No9

文件中包含word文档报告 设雷达采用匹配滤波完成脉冲压缩，采集频率fs=420MHz，仿真雷达回波，并绘出家Hamming窗前后的脉压波形。（提示：通过正确设定采集波门，减少数据量） 设雷达采用Dechirp方式完成脉冲压缩，其中参考距离位于（0，0），采集频率为10MHz，距离采样点数512点，仿真雷达回波，并绘出加Hamming窗前后的脉压波形（提示：通过正确设定采集波门，减少数据量）。(Word document file contains the report of the completion of matched filter-based radar uses pulse compression, gathering frequency fs = 420MHz, simulation of radar echo, and draw the house after the pulse pressure waveform Hamming window. (Hint: By setting the correct collection wave door, reducing the amount of data), based radar uses pulse compression Dechirp manner, in which reference distance at (0,0), collection frequency of 10MHz, from the sampling points 512 points, simulation, radar echo, and draw the increase of pulse pressure waveform after the Hamming window (hint: set up collection waves through the correct door, reducing the amount of data).)

1． 该光盘包含了“信号与系统分析及MATLAB实现”一书的第七章所有程序； 2． 为了方便读者阅读程序，所有程序均采用中文注释。MATLAB的程序编辑器不支持中文显示，用户只需在Word下直接打开源程序文件，即可阅读程序中的中文注释； 3． 程序文件的命名分为以下三种类型： （1） 若为书中例题的程序，则程序文件名一律以ex开头，后面跟4位数字（前两位表示章号，后两位表示例题序号）表示的该程序所在例题的编号。例如，ex0603.m是例6.3的程序，而ex1102.m则是例11.2的对应程序。 （2） 若为书中图形的实现程序，则程序文件名一律以figure开头，后面跟4位数字（前两位表示章号，后两位表示图形序号）表示的该程序所绘图形的编号。例如，figure1203.m是实现图12.3的程序，而figure0710.m则是实现图7.10的对应程序。 （3） 若为函数文件，则直接以函数名命名，例如文件sconv.m即是书中函数sconv()的对应程序。 ()

说明：  计算弯曲线天线的输入阻抗，辐射方向图以及增益（可以计算不同的直线长度，弯折次数，弯折高度，弯折角度的弯曲线天线）(Calculation of bending wire antenna input impedance, radiation pattern and gain (the straight line can be calculated in different length, bending frequency, a high degree of bending, bending angle of bending wire antenna))

说明：  迭代学习控制源代码，希望学习次控制方法的朋友能和我交换资源(Iterative learning control source code, want to learn controls the method of exchange of resources and my friends can)