登录
首页 » matlab » keli_catch

keli_catch

于 2013-07-28 发布 文件大小:428KB
0 238
下载积分: 1 下载次数: 3

代码说明:

  颗粒提取,用于MATLAB仿真的,提取一些细小的颗粒。效果较好。(Particle extraction for the MATLAB simulation, extract some small particles. Better.)

下载说明:请别用迅雷下载,失败请重下,重下不扣分!

发表评论

0 个回复

  • dpsk
    dpsk调制解调及相应误码率计算。随机产生正弦信号并进行调制解调。(dpsk modem and the corresponding bit error rate. Randomly generated sinusoidal signal and modem.)
    2011-05-13 12:23:32下载
    积分:1
  • bianjiezhuliejianche
    实现一维边界逐列检测,程序可在MATLAB环境下运行(achieve an out-by-dimensional border detection process will be run under MATLAB)
    2007-05-07 10:47:16下载
    积分:1
  • obs_matlab
    MATLAB programs for Full state observer and reduced order state observer which is used in regulator system has the plant with Ackermann Formula. this code is used in control system engineering .
    2013-11-19 23:37:13下载
    积分:1
  • matlabgenetictoolbox
    此工具箱是英国设菲尔德(Sheffield)大学编写的MATLAB遗传算法工具箱,是使用的最广泛的遗传工具箱之一。在《MATLAB 遗传算法工具箱及应用》作 者:雷英杰 出版社:西安电子科技大学出版社 这本书中重点介绍了此工具箱。( Sheffield genetic matlab toolbox)
    2009-05-04 17:24:27下载
    积分:1
  • CamShift-matlab
    说明:  camshift的matlab源代码,已经测试通过(camshift the matlab source code has been tested)
    2021-04-01 10:59:08下载
    积分:1
  • pca-code-simple
    pca face recognition
    2011-08-20 21:19:50下载
    积分:1
  • LEACHThe-routing-protocol-improved
    本文提出了一种节点密度和剩余能量传感器网络加权分群算法,该分群算法优化了群首 选择,均衡了网络节点的能量消耗,延长了网络的生命周期(This paper proposes a residual energy of sensor nodes in the network density and weighted clustering algorithm, the clustering algorithm to optimize the group' s first choice, balancing the energy consumption of network nodes to extend the network life cycle)
    2011-10-04 17:25:15下载
    积分:1
  • MYwhile
    使用MATLAB工具箱LMI求解线性矩阵不等式,使用WHILE循序求解最小值。(Using the MATLAB LMI toolbox for solving linear matrix inequalities, solving the minimum sequential use of WHILE.)
    2010-11-06 16:50:17下载
    积分:1
  • wavelet
    直扩系统中,非抽取小波包变换抑制窄带干扰。(narrowband interference suppression with the wavelet packet transform.)
    2011-04-30 20:35:43下载
    积分:1
  • matlab
    数字控制系统仿真与综合应用:设控制对象为 W1=10/s(1+0.1s)(1+0.05s),采样周期T=0.2s。 (1)采用零阶保持器,将W1(s)转换成W1(z),串接一个计算机调节模型D(z)组成一个典型的数字反馈系统。分别用仿真方法得到系统在单位阶跃输入作用下的响应和系统在单位速度输入时的输出响应。 (Digital control system simulation and comprehensive application: set control object for W1 = 10/s (1+ 0.1 s) (1+ 0.05 s), the sampling period T = 0.2 s. (1) the zero order keep device, will W1 (s) convert W1 (z), the combination of a computer adjusting model D (z) composed of a typical digital feedback system. The simulation method were used to get in the unit step input system under the action of response and system in the unit of output response speed input. )
    2012-04-19 14:38:25下载
    积分:1
  • 696516资源总数
  • 106914会员总数
  • 0今日下载