xiaobobianhuan

牛顿迭代算法牛顿迭代算法 matlab牛顿迭代算法牛顿迭代算法 matlab牛顿迭代算法牛顿迭代算法 matlab牛顿迭代算法牛顿迭代算法 matlab牛顿迭代算法牛顿迭代算法 matlab牛顿迭代算法牛顿迭代算法 matlab牛顿迭代算法牛顿迭代算法 matlab (Newton iterative algorithm iterative algorithm of Newton Newton algorithm matlab matlab Newton Newton algorithm algorithm algorithm matlab Newton Newton Newton algorithm algorithm algorithm matlab Newton Newton Newton algorithm Newton algorithm matlab Newton iterative algorithm iterative algorithm matlab matlab Newton algorithm)

说明：  地球物理勘探过程中对地震记录数据进行成像(Geophysical data during the imaging of seismic records)

波前曲扭和幅度变化对阵列测向中相干源分辨的影响(Twisted and curved wavefront amplitude variation to distinguish the impact of coherent source direction finding in an array)

基于多相催化反应动力学的特点和基本原理,提出多相催化反应动力学方程的一般形式,并介绍了用Matlab语言设计确定多相催化反应动力学方程参数的通用程序.处理时先对实验测定不同时刻对应的反应速率v0和浓度C(或压力P),利用无约束最优化计算方法求出多相催化反应动力学方程参数.文中以镍硅藻土催化苯加氢合成环己烷的实验数据为例进行验证,结果表明,利用所编程序确定的动力学方程和理论值及文献值很好吻合.(Based on the characteristics and dynamics of the basic principles of heterogeneous catalysis, heterogeneous catalysis proposed general form of kinetic equation and introduces heterogeneous catalytic reaction kinetics equation to determine the parameters used in Matlab language design common procedures when handling the first experimental measured at different times corresponding to the concentration of the reaction rate v0 and C (or pressure P), the use of unconstrained optimization calculations obtained heterogeneous catalytic reaction kinetics equation parameters. text nickel diatomaceous earth catalytic hydrogenation of benzene cyclohexane an example to validate the experimental data, the results show that the equations and theoretical value and dynamics literature values ​ ​ determined using the programmed good match.)

一个有用的声学回声消除器的设计源码，还不错哦～(A useful acoustic echo cancellation design source, oh well ~)

single phase active harmonic filter

利用FFT方法和维纳-辛钦定理自相关函数获得功率谱的对比。(Using FFT method and Wiener- Khintchine theorem to obtain the autocorrelation function of the power spectrum contrast.)

PSO theory explanation

数字控制系统仿真与综合应用：设控制对象为 W1=10/s(1+0.1s)(1+0.05s),采样周期T=0.2s。 （1）采用零阶保持器，将W1(s)转换成W1(z),串接一个计算机调节模型D(z)组成一个典型的数字反馈系统。分别用仿真方法得到系统在单位阶跃输入作用下的响应和系统在单位速度输入时的输出响应。 (Digital control system simulation and comprehensive application: set control object for W1 = 10/s (1+ 0.1 s) (1+ 0.05 s), the sampling period T = 0.2 s. (1) the zero order keep device, will W1 (s) convert W1 (z), the combination of a computer adjusting model D (z) composed of a typical digital feedback system. The simulation method were used to get in the unit step input system under the action of response and system in the unit of output response speed input. )

tugas pcd untuk proyek akhir