85375555Tracking

说明：  利用Matlab编写程序实现以下功能：以多项式形式输入系统前向通路传递函数和反馈回路传递函数，计算系统开环增益，判定型别，根据控制系统劳斯稳定判据原理，列出得到的任意阶次系统的劳斯表，判定闭环系统稳定性，若不稳定给出具有正实部极点的数目。 （1）根据用户输入的稳定度a，计算稳定的开环增益K的范围； （2）确定系统的最大稳定度a,计算相应的开环增益K的值。 (The use of Matlab programming to achieve the following functions: polynomial in the form of input system transfer function to the path and feedback loop transfer function, system open-loop gain calculation to determine type, according to Routh stability criterion control system theory, has been listed in the system of arbitrary order Routh table to determine the stability of the closed-loop system, if the stability of a positive real part gives the number of poles. (1) According to the stability of the user to enter a, calculation of the stability of the open-loop gain of the scope of K (2) to determine the most stable system a, the calculation of the open-loop gain of the corresponding K value.)

说明：  一个完整的adrc源码资料，对adrc学习者会有帮助(adrc matlab software toutin)

计算PSNR。可直接调用，两个输入参数im1,im2为两个图象序列，返回值为PSNR的值。(Calculation of PSNR. Can be called directly, two input parameters im1, im2 two image sequences, the return value is the PSNR.)

matlab编程实现OQPSK调制解调波形及频谱、功率谱的绘图( 您是不是要找： matlab编程实现QPSK调制解调形及频谱、功率谱的绘图 matlab programming OQPSK modulation and demodulation waveform and spectrum, power spectrum drawing)

基于FDTD算法，用MATLAB实现了波导色散特性的仿真研究(Based on the FDTD algorithm, implemented using MATLAB simulation of waveguide dispersion characteristics)

一个比较老的水印程序 MATLAB写的 (Watermarking a relatively old procedure written in MATLAB)

一种未知输入/输出的解耦方法，可用于控制器的设计、故障诊断系统设计等(An unknown input/output decoupling method can be used for controller design, fault diagnosis system design)

基于均匀线阵，利用四阶累积量产生虚拟阵元，可估计出比真实阵元数更多的信号源，已达到DOA估计的目的，且具有较好的分辨率。(Based on uniform linear array, using fourth-order cumulants to generate the virtual array element can be estimated more than the true number of array element signal source, the purpose has been to DOA estimation, and has good resolution.)

魔方还原程序,主函数为Cube,采用CFOP，还原步骤为88步左右，底面十字未优化；采用留个3*3矩阵，前面为froo（数字3），后面为baa（数字-3），左面为leff（数字-2），右面为rigg（数字2），上面为upp（数字0），下面为doo（数字1），(Cube restore process, the main function of Cube, using CFOP, the reduction step is 88 steps or so, the bottom cross unoptimized adopt leave a 3* 3 matrix, in front of froo (figure 3), followed by the baa (figure-3), left the leff (digital-2), the right of rigg (figure 2), at the upp (number 0), following the doo (figure 1),)

Important matlab code for research