111

sync generator pscad

用GAL16V8设计可变长度序列信号发生器，在掌握伪随机序列性质的基础上，设计给定长度的伪随机序列信号发生器，也即设计给定n后（n为移位寄存器的级数）最长线性反馈移位寄存器序列。并在给定n产生的最长序列的基础上，截短出课题给出的序列长度，并用FM软件对可编程器件GAL16V8进行编程，以实现长度不同的序列信号发生器。(GAL16V8 design variable-length sequence signal generator based on the master pseudo-random sequence nature, the design of a given length pseudo-random sequence Signal generator, designed for the series) up to linear feedback shift register sequences given n (n is the shift register. And given n Sequence length given by the subject on the basis of the longest sequence, truncated, and FM software for programming the programmable device GAL16V8, in order to achieve Different length of the sequence signal generator.)

交错并联功率因数校正方案，从TI官方网站上下的(Interleaved power factor correction schemes, down from TI' s official website)

在低风速情况下，风力发电机组的先进变桨距控制策略的程序(Low Wind Speed Turbine Project Conceptual Design Study: Advanced Independent Pitch Control)

本文实现了光缆监测站自动监测终端设备的设计方案，通过嵌入式硬件系统和软件的协同工作，该监测设备能够对通信光缆进行在线实时监测，并且能够实时探测到通信光缆的故障点，方便了通信光缆的维护工作。该系统在业务板卡的设计，以及CAN控制通信总线的使用都增强了设备的兼容性和系统的可扩展性，并且增加了环境监测单元来自动调节环境温度，以保证系统安全可靠运行。(This automatic monitoring stations to achieve a fiber optic terminal equipment design, through the embedded hardware systems and software work together, the monitoring device can communicate on-line real-time monitoring of fiber optic cable and communication cable in real time to detect the point of failure, to facilitate the communication cable maintenance. The system is in the business card design, and the use of CAN bus control communication devices have enhanced compatibility and system scalability, and increased environmental monitoring unit to automatically adjust the temperature to ensure the system safe and reliable operation.)

LPC1788官方原理图文件，PCB文件暂时我也没有，不过在设计时这篇文档还是有极大参考(LPC1788 official schematic documents, PCB files temporarily I did not, but in the design of this document or a great reference)

数据库系统课程设计(Database System Design Course)

说明：  便携式表面粗糙度仪设计与实现Portable surface roughness instrument design and implementation(Portable surface roughness instrument design and implementation)

设计了一基于现场可编程门阵列（FPGA）的低频数字式相位测量仪。该测量仪包括数字式移相信号发生器和相位测量仪两部分，分别完成移相信号的发生及其频率、相位差的预置及数字显示、发生信号的移相以及移相后信号相位差和频率的测量与显示几个功能。其中数字式移相信号发生器可以产生预置频率的正弦信号，也可产生预置相位差的两路同频正弦信号，并能显示预置频率或相位差值；相位测量仪能测量移相信号的频率、相位差的测量和显示。两个部分均采用基于FPGA的数字技术实现，使得该系统具有抗干扰能力强, 可靠性好等优点。()

矢量控制与直接转矩控制是当前主要的两种电机变频调速控制方法，已在两相交流感应电机中得到 了应用。分析了两相不对称电机矢量控制和直接转矩控制原理以及两相三桥臂逆变器的SVPWM实现方法； 运用Matlab的Simulink建立了两相不对称交流感应电机矢量控制和直接转矩控制调速系统的仿真模型，并 对两种控制系统进行了仿真研究，给出了仿真波形，进行了特性比较． 关键词：两相电机；矢量控制；直接转矩控制；SVPWM；MATLAB；仿真(Vector Control and Direct Torque Control is currently the main method of frequency control of two motors, has been in two-phase AC induction motor has been applied. Analysis of asymmetric two-phase motor vector control and direct torque control principle and two-phase SVPWM inverter arm Bridge Implementation the use of Matlab in Simulink to establish a two-phase AC induction motor asymmetry of vector control and direct torque control modulation speed of system simulation models, and the two control system was simulated, the simulation waveform characteristics were compared. Key words: two-phase motor vector control direct torque control SVPWM MATLAB Simulation)