3_Onduleur-3-niveaux--NPC

信源函数 randerr 产生比特误差样本 randint 产生均匀分布的随机整数矩阵 randsrc 根据给定的数字表产生随机矩阵 wgn 产生高斯白噪声 信号分析函数 biterr 计算比特误差数和比特误差率 eyediagram 绘制眼图 scatterplot 绘制分布图 symerr 计算符号误差数和符号误差率 信源编码 compand mu律/A律 压缩/扩张 dpcmdeco DPCM（差分脉冲编码调制）解码 dpcmenco DPCM编码 dpcmopt 优化DPCM参数 lloyds Lloyd法则优化量化器参数 quantiz 给出量化后的级和输出值 误差控制编码 bchpoly 给出二进制BCH码的性能参数和产生多项式 convenc 产生卷积码 cyclgen 产生循环码的奇偶校验阵和生成矩阵 cyclpoly 产生循环码的生成多项式 decode 分组码解码器 encode 分组码编码器 gen2par 将奇偶校验阵和生成矩阵互相转换 gfweight 计算线性分组码的最小距离 hammgen 产生汉明码的奇偶校验阵和生成矩阵 rsdecof 对Reed-Solomon编码的ASCII文件解码(#include <math.h> #include <stdio.h> #include <stdlib.h> #include <ctype.h> #include <float.h> #include <string.h> #include <stdarg.h> #include "svm.h" )

对网络划分社区,并找出最大的社区,很有用的程序(Find the largest giant component)

梯形轨迹规划函数，其路径是抛物线混合线性段，其速度为梯形(The path of the ladder path planning function, the path is a parabolic mixed linear section, the speed of which is a trapezoid.)

地震波作用下计算地震加速度、速度、位移反应谱(Computation of seismic response spectrum)

电网电压稳定状态下的双馈风机磁通观测，可用于定子磁通的观测(Quasi steady-state magnitude of flux at generator stator)

Hough transform-Using Matlab,we implement a system that detects the indicated coins.(Hough transform-Using Matlab, we implement a system that detects the indicated coins.)

一种基于小波变换的灰度数字水印嵌入算法,使用matlab实现，含有原始论文。不过不是很理想，希望大家改进(Gray-scale based on wavelet transform digital watermark embedding algorithm, using matlab implementation, containing the original papers. But not very good, hope that we improve the)

MT9075为E1接口芯片MT9075为E1接口芯片MT9075为E1接口芯片(Combined pcm30 framer,line interface unit and link controllers in a 68pin PLCCor 100 pin MQFPpackage)

用LAPLACE方法求解多维沃尔泰拉方程，此处为一个变元的方程，由于该方程同时含有微分和积分，一般求解有一定的困难。此处为MATLAB程序，注意不同的边界条件(used method for multiple preoperational Ertaila equation here as a variable element of the equation, As the same time contain differential equations and integral, the general solution is definitely difficult. MATLAB here for the procedures, attention to the different boundary conditions)

eigen matrix will automatically delete the directory of debug and release The content is too simple Is not a sourcecode or document Description is not detailed or not correct