server

输控制协议（TCP，Transmission Control Protocol）是一种面向连接的、可靠的、基于字节流的传输层通信协议，由IETF的RFC 793定义。TCP旨在适应支持多网络应用的分层协议层次结构。(Transmission Control Protocol (TCP) is a connection-oriented, reliable, byte-stream-based transport layer communication protocol defined by IETF RFC 793. TCP aims at adapting to the hierarchical protocol structure supporting multi-network applications.)

说明：  使用usrp n210,利用Labview实现正弦信号收发，一方面可以利用labview实现实际信号在空中收发，另一方面可以检验设备正常运行。(Using USRP N210 and Labview to transmit and receive sinusoidal signals, on the one hand, it can use LabVIEW to transmit and receive actual signals in the air, on the other hand, it can check the normal operation of the equipment.)

说明：  上位机使用LABVIEW显示心跳曲线， USB采集，单片机采用STM32F103C8，心跳检测芯片采用AD8232，利用单片机自身AD转换(The upper computer uses LabVIEW to display the heartbeat curve, USB to collect, SCM uses stm32f103c8, heartbeat detection chip uses ad8232, SCM uses its own ad conversion)

虚拟仪器的网络控制 1）、设计一个程序控制8个外设小灯的点亮方式，要求两种方式A:每个小灯间隔时间T，依次亮，时间T可调，并循环。B：先1.3.5.7.9亮隔时间T，2.4.6.8.10亮，并循环，T可调。 2）、要求主面板与硬件的8个小灯同步。 3）、通过网络在另一台计算机上控制此程序的运行（利用LabVIEW的DateSocket技术）((Network control of virtual instruments 1), design a program to control eight peripheral lights lit the way, the requirements in two ways A: each light interval T, followed by bright, time T adjustable, and circulation. B: first 1.3.5.7.9 bright every time T, 2.4.6.8.10 light, and circulating T-adjustable. 2), requires eight small lights of the main panel and hardware synchronization. 3), through the network control of this program running on another computer (using the LabVIEW DateSocket technology)))

产生0到100kd的方波。正玄波，三角波，锯齿波和输出为0到10V的电压的信号发生器(0 to 100kd produce a square wave. Sine wave, triangle wave, sawtooth wave and the output voltage from 0 to 10V signal generator)

labview 双通道信号采集和回放系统，可以实现信号采集，设置频率(labview dual-channel signal acquisition and playback system that can achieve signal acquisition, set the frequency)

基于NI SCOPE的数据实时采集，并进行采集数据的写入保存。程序实现了采集原理，可以进行数据的后续处理(NI SCOPE-based real-time collection of data, and for the collection of data written to save it. Program for the acquisition principle, the follow-up data processing)

对电机进行手动控制，改变电机转速完成实验教学演示目的 (Manual control of the motor, changing the motor speed to complete the experimental teaching demonstration purposes)

简易计算器，实现加、减、乘、处、开方等功能。(Simple calculator to add, subtract, multiply, at the square root function.)

基于labview平台的虚拟示波器，能实现基本的示波器功能。(The virtual oscilloscope based on LabVIEW platform can realize the basic oscilloscope function.)