autocorrelationfunction

说明：  Introduction of NI data acquisition hardware 1. Basic components of a complete data acquisition system 2. NI provides data acquisition hardware products based on which platforms and which application areas they are suitable for respectively. 3. What important parameters should be paid attention to in the process of hardware selection of data acquisition equipment

The structure of the multilayer sequence

说明：  神经网络在数据处理或模式识别中具有重要作用，这里采用LabVIEW实现了神经网络的功能，供工程师使用。(Neural networks play an important role in data processing or pattern recognition. LabVIEW is used here to implement the functions of neural networks for engineers to use.)

通过串口读取定位数据，然后进行定位数据解析与显示。(The positioning data is read through the serial port, and then the positioning data is parsed and displayed.)

1）、设计一个程序控制8个外设小灯的点亮方式，要求两种方式A:每个小灯间隔时间T，依次亮，时间T可调，并循环。B：先1.3.5.7.9亮隔时间T，2.4.6.8.10亮，并循环，T可调。 2）、要求主面板与硬件的8个小灯同步。 3）、通过网络在另一台计算机上控制此程序的运行（利用LabVIEW的DateSocket技术）((Network control of virtual instruments 1), design a program to control eight peripheral lights lit the way, the requirements in two ways A: each light interval T, followed by bright, time T adjustable, and circulation. B: first 1.3.5.7.9 bright every time T, 2.4.6.8.10 light, and circulating T-adjustable. 2), requires eight small lights of the main panel and hardware synchronization. 3), through the network control of this program running on another computer (using the LabVIEW DateSocket technology)))

2013最新版声音震动模块手册详细介绍了使用方法(2013 New Sound and Vibration Toolkit)

优点：1，PPI协议通讯速度快，比OPC ，PCAccess，Modbus 快4-5倍左右。(就这一条优点就足了，呵呵) 2，PLC端无需编写任何通讯程序。 3，可以直接对PLC进行，RUN STOP等操作。 4，本程序全部采用LABVIEW底层程序框图，没用调用任何的DLL ，API等。这点对你学习还是修改程序功能都很有帮助，方便。 (Advantages: 1, PPI protocol communications faster than OPC, PCAccess, Modbus about 4-5 times faster. (On which an advantage on the feet, huh, huh) 2, PLC-side without writing any communication program. 3, can be carried out directly on the PLC, RUN STOP operation. 4, the procedure used in all LABVIEW underlying the block diagram, useless to call any DLL, API, etc. This is for you to learn or modify the program features are very helpful and convenient.)

labview与机械手的九点标定 手眼标定的实现(LabVIEW and nine-point calibration of manipulator)

说明：  可以对单次输入的信号进行滤波分析和图像显示。同时也具备暂停和历史图像保存的功能。 本程序主要针对的是低频率的未知信号，对于高频率信号最好采用单次采样的方式。(The single input signal can be filtered and analyzed, and the image can be displayed. It also has the functions of pausing and preserving historical images. This program is mainly for low frequency unknown signals, for high frequency signals, the best way to use a single sampling.)

labview环境下的CAN总线上位机模块，使用的CAN 卡为周立功usbcan(CAN bus PC in labview environment, CAN card for ZLG)