登录
首页 » matlab » bimodal-noise

bimodal-noise

于 2011-04-30 发布 文件大小:2KB
0 215
下载积分: 1 下载次数: 61

代码说明:

  在复杂的电子系统中,影响信号接收的很多噪声为非高斯噪声,这些噪声是没有预料到的,以致破坏了接收机的功能,研究表明:这些噪声可以看成双模噪声,双模噪声从整体上讲属于非高斯噪声。(In complex electronic systems, many of the signal received by a non-Gaussian noise, the noise is not anticipated, resulting in damage to the receiver function, research shows that: the noise can be regarded as dual-mode noise, dual-mode noise As a whole is non-Gaussian noise.)

下载说明:请别用迅雷下载,失败请重下,重下不扣分!

发表评论

0 个回复

  • MXY5
    说明:  计算固体作业 分析桥梁的结构 各种参数的变化(Solid job of calculating the structure of the bridge)
    2011-03-23 21:32:49下载
    积分:1
  • Sep-protocol_enrgy
    Sep protocol in wireles sensor network
    2013-11-05 12:28:33下载
    积分:1
  • biseccion.m
    Bisection method matlab
    2012-01-26 20:29:17下载
    积分:1
  • rte
    edge detection using fuzzy 1...............................................
    2012-02-06 15:02:38下载
    积分:1
  • floyd
    matlab floyd最短路算法。。。。
    2010-08-20 21:28:52下载
    积分:1
  • CompressedSensing
    用于快速处理压缩感知的程序。输入原向量及其长度即可得出压缩前向量。(需要使用pdco.m文件。)(For fast processing of compressed sensing program. Enter the original vector and its length can be derived before compression vector. (Need to use pdco.m file.))
    2013-04-16 23:10:23下载
    积分:1
  • 8.-FILTER
    Power quality generation of voltage sags. All kinds of sags can be generated.
    2014-09-09 21:46:16下载
    积分:1
  • Robot-arm-non-standard-LQR-Control
    单级机械臂的位置控制,由于需要调整时间和最大输入力矩的要求,程序实现两种非标准的LQR控制(The single-stage manipulator position control, due to the need to adjust the time and the maximum input torque requirements of the program to achieve the two non-standard LQR control)
    2012-08-20 11:13:19下载
    积分:1
  • OFDM
    首先根据短训练字的特性进行相关运算,进行信号到达检测,当检测到相关值大于门限一定次数后,认为有信号到达。然后根据长训练字的特性,进行相关运算,进行OFDM符号FFT窗口起始位置的估计。估计出FFT窗口的位置后,先在时域进行小频偏的估计,将两个长训练字进行小频偏补偿后,进行FFT运算,根据FFT运算的结果进行整数倍频偏的估计。这些参数估计完成后,就可以进行数据解调了。先对数据部分进行完整的频偏补偿,然后根据估计的FFT窗口位置进行FFT运算得到频域的数据,进行解调。然后在对应于导频的子载波位置上提取出导频信息,根据导频信息估计出剩余定时误差以及剩余的信道响应误差,将误差量送入环路进行跟踪。当收到所有数据后,重新回到信号到达检测状态,进行下一次信号到达的检测和信号接收。(First, according to the characteristics of the short training word correlation operation, the signal reaching the detector, when the detected correlation value is greater than the threshold after a certain number of times that a signal arrives. And then the characteristics of long training word, the correlation operation for the FFT window starting position of an OFDM symbol estimate. The estimated position of the FFT window, the first small frequency offset in the time domain estimation, the two long training word small frequency offset compensation, the FFT operation, the FFT result of the operation for integer frequency offset estimate. These parameter estimation is completed, the data can be demodulated on. The first portion of the data for a complete frequency offset compensation, and based on the estimated FFT window position of the FFT operation to obtain frequency domain data, demodulated. Then corresponding to the position of the pilot subcarriers are extracted on pilot inform)
    2020-11-04 23:49:52下载
    积分:1
  • improved_jakes
    This code implies the improved Jakes Method( Y. R. Zheng and C. Xiao, Improved models for the generation of multiple uncorrelated Rayleigh fading waveforms, IEEE Comm. Lett., vol. 6, no. 6, pp. 256-258 (2002) ) to simulate Rayleigh fading
    2009-06-29 20:16:20下载
    积分:1
  • 696516资源总数
  • 106914会员总数
  • 0今日下载